Western Members CA, AZ, NV, UT, CO, NM, HI

My car went under the knife today...

Thread Tools
 
Search this Thread
 
Old 05-22-2009, 12:03 PM
  #61  
Staging Lane
iTrader: (1)
 
rican_boi310's Avatar
 
Join Date: Apr 2007
Location: Hawthorne, CA
Posts: 71
Likes: 0
Received 0 Likes on 0 Posts
Default

That's great!!! I can't wait to do my rebuild!! I'm going to CMS also!!
Old 05-22-2009, 12:06 PM
  #62  
On The Tree
 
jester ls1's Avatar
 
Join Date: Nov 2008
Location: Spring TX
Posts: 182
Likes: 0
Received 0 Likes on 0 Posts
Default

Nice!
Old 05-22-2009, 07:55 PM
  #63  
TECH Fanatic
Thread Starter
iTrader: (71)
 
MrElectric03's Avatar
 
Join Date: Dec 2007
Location: Southern California
Posts: 1,885
Likes: 0
Received 1 Like on 1 Post

Default

Thanks guys, Yea CMS is a great shop, they are busy but for a reason. Im very happy with the outcome.
Old 05-22-2009, 08:39 PM
  #64  
10 Second Club
iTrader: (53)
 
geovett's Avatar
 
Join Date: Apr 2007
Location: So.Ca.(I.E.)
Posts: 409
Likes: 0
Received 1 Like on 1 Post

Red face

Hey Ryan, good job!!!!.. you saved lots of $$$$$..doing the R&R!!!!..
are u ready to Rumble????...ha....i did a 7.4 last nite on Just Motor didn't get
a chance to apply the sauce......are you going to be ready for Invasion???
sounds like u r......
Old 05-22-2009, 10:00 PM
  #65  
LS1TECH Sponsor
iTrader: (10)
 
Ryne @ CMS's Avatar
 
Join Date: Apr 2004
Location: murrieta
Posts: 2,774
Likes: 0
Received 2 Likes on 2 Posts

Default

that torque still amazes me...... but that was the intention when i advance the intake 4 degrees, but i wasnt suspecting that much torque, but with the right cam and compression torque can be made
Old 05-23-2009, 02:51 AM
  #66  
12 Second Club
iTrader: (5)
 
krazy4's Avatar
 
Join Date: Mar 2006
Location: Yorba Linda, CA
Posts: 1,457
Likes: 0
Received 3 Likes on 3 Posts

Default

Nice numbers!!!!

Time for the giggle juice!
Old 05-23-2009, 05:16 AM
  #67  
TECH Junkie
iTrader: (4)
 
Soul TKR's Avatar
 
Join Date: Jun 2004
Location: San Diego, CA
Posts: 3,543
Likes: 0
Received 1 Like on 1 Post

Default

Originally Posted by MrElectric03
Well the results are in!

I have an oxy sensor cutting in and out so im going back today to install a couple new denso oxy sensors and have Ryne clean up the idle a little bit.

Tha final numbers were 468 RWHP and 434 RWTQ!

I was expecting about 460rwhp and 410rwtq so that torque being up there surprised both Ryne and I.

The cars running great and has lots of power, I can tell a good difference from the old setup.

Big thanks to Ryne for staying until after 1am to get it done!
that's it!!! I need a bigger cam

been thinking for a while of getting a 96/96 combo with a larger cam... just not sure which one yet... but I wanna get as close to 500rwhp as possible NA

Killer numbers bro!

UPDATE THAT SIG!

Last edited by Soul TKR; 05-23-2009 at 05:21 AM.
Old 05-23-2009, 10:09 AM
  #68  
TECH Fanatic
Thread Starter
iTrader: (71)
 
MrElectric03's Avatar
 
Join Date: Dec 2007
Location: Southern California
Posts: 1,885
Likes: 0
Received 1 Like on 1 Post

Default

Originally Posted by geovett
Hey Ryan, good job!!!!.. you saved lots of $$$$$..doing the R&R!!!!..
are u ready to Rumble????...ha....i did a 7.4 last nite on Just Motor didn't get
a chance to apply the sauce......are you going to be ready for Invasion???
sounds like u r......
Well im hoping to pick up a pair of prostars today for my ET Streets, if not Will is going to loan me some MT DRs. Thats a good time man, if thats on motor im not sure ill have a chance with you on spray, ill have to get my juice on and well go to irwindale one of these weeks.
Old 05-23-2009, 10:14 AM
  #69  
TECH Fanatic
Thread Starter
iTrader: (71)
 
MrElectric03's Avatar
 
Join Date: Dec 2007
Location: Southern California
Posts: 1,885
Likes: 0
Received 1 Like on 1 Post

Default

Originally Posted by Soul TKR
that's it!!! I need a bigger cam

been thinking for a while of getting a 96/96 combo with a larger cam... just not sure which one yet... but I wanna get as close to 500rwhp as possible NA

Killer numbers bro!

UPDATE THAT SIG!
The 96/96 is nice, if I had a larger cube motor is go to the 100mm tb and port the opening of the intake but I dont think it would do anything for a 347.

With your combo and a larger cam with a FAST you should be pretty close to 500 wheel...send that car to CMS!.....updating sig



Quick Reply: My car went under the knife today...



All times are GMT -5. The time now is 02:47 AM.