12secSS

iTrader: (30)

I have a couple of items I would like to sell from Jen's car. All prices are including shipping, unless otherwise specified. Trades may be entertained. I am negotiable on all items.

Hybrid Nitrous system
10lb NOS Bottle (blue) with blowdown tube, pressure gauge and mounting brackets
Nitrous solenoids, One NX and One NOS (IIRC)
8' Steel Braided Line for N2O, basically it runs from the spare tire area along the passenger's side then over to the driver's front shock tower
Asking $330 obo
http://www.jenibellaracing.com/ForSale/N2O-1.JPG
http://www.jenibellaracing.com/ForSale/N2O-2.JPG
http://www.jenibellaracing.com/ForSale/N2O-3.JPG
http://www.jenibellaracing.com/ForSale/N2O-4.JPG
http://www.jenibellaracing.com/ForSale/N2O-5.JPG
http://www.jenibellaracing.com/ForSale/N2O-6.JPG

TSP 78mm Lid, black
Asking $65 obo Sale Pending
http://www.jenibellaracing.com/ForSale/TSP-Lid-1.JPG
http://www.jenibellaracing.com/ForSale/TSP-Lid-2.JPG
http://www.jenibellaracing.com/ForSale/TSP-Lid-3.JPG

OEM Center Bolt Valve Covers, with Oil Fill Tube
Asking $120 each set (I have two sets) obo
http://www.jenibellaracing.com/ForSale/Valve-Covers.JPG

Coil Brackets for Center Bolt VC, with coil pack hardware
Asking $40 (1 set) obo
http://www.jenibellaracing.com/ForSale/Valve-Covers.JPG

SLP Y-Pipe
OEM replacement type
NOT FOR LONG TUBES
Asking $130 obo
http://www.jenibellaracing.com/ForSale/SLP-Ypipe-1.JPG
http://www.jenibellaracing.com/ForSale/SLP-Ypipe-2.JPG
http://www.jenibellaracing.com/ForSale/SLP-Ypipe-3.JPG
http://www.jenibellaracing.com/ForSale/SLP-Ypipe-4.JPG

Custom LS1 Cam
Single Pattern, Hydraulic
246 Dur. @ .050" Lift
.603" Valve Lift
113 LSA
Was used on factory stock short block, minor valve relief maybe required if heads are milled
Asking $350 obo
http://www.jenibellaracing.com/ForSale/LS1-Cam-1.JPG
http://www.jenibellaracing.com/ForSale/LS1-Cam-2.JPG
http://www.jenibellaracing.com/ForSale/LS1-Cam-3.JPG
http://www.jenibellaracing.com/ForSale/LS1-Cam-4.JPG

Dynojet Wideband Commander
Includes Autometer white face AFR analog gauge
Wideband O2 sensor (Bosch #17033) is bad
Will work with any other Bosch wideband, just receptacles are different
Includes datalogging software
Asking $300 obo
http://www.jenibellaracing.com/ForSale/Wideband-1.JPG
http://www.jenibellaracing.com/ForSale/Wideband-2.JPG

Granetelli MAS
Red, ends were modified, but still flows fine
Asking $100 obo
http://www.jenibellaracing.com/ForSale/GMAS-1.JPG
http://www.jenibellaracing.com/ForSale/GMAS-2.JPG

1998 Cassette Radio from a Z28
Good condition, still works fine
Asking $60 obo
http://www.jenibellaracing.com/ForSale/Radio-1.JPG
http://www.jenibellaracing.com/ForSale/Radio-2.JPG
http://www.jenibellaracing.com/ForSale/Radio-3.JPG
http://www.jenibellaracing.com/ForSale/Radio-4.JPG

1998 ECM
Came out of our Camaro
I can reflash it to a stock M6 or A4 file
PM me if you would like additional changes made to the stock file
Asking $100 obo
http://www.jenibellaracing.com/ForSa...Body-ECM-1.JPG
http://www.jenibellaracing.com/ForSa...Body-ECM-2.JPG
http://www.jenibellaracing.com/ForSa...Body-ECM-3.JPG

SLP Driveshaft Loop
Never used
Asking $120 obo
http://www.jenibellaracing.com/ForSa...-DS-Loop-1.JPG
http://www.jenibellaracing.com/ForSa...-DS-Loop-2.JPG

For you Holley Intake owners, I have the Throttle Body and Base gaskets
I used the head gaskets for our (GMPP) intake, but have no use for these extra gaskets.
Asking $30 obo
http://www.jenibellaracing.com/ForSa...ey-Gaskets.JPG

Used Spark Plug Wires
Good condition
Asking $10 (to cover shipping cost only) obo
http://www.jenibellaracing.com/ForSale/Plug-Wires.JPG

Reese Class III Trailer Hitch
For use with a 2" shank ball
3-1/4" Drop or 2" Rise
Asking $20 obo
http://www.jenibellaracing.com/ForSale/Hitch.JPG