01Blk*SS*

iTrader: (4)

they guys that say they run 305's, is that on a 19x11?

Mr.z/28

iTrader: (8)

19x 10 from what I know...

01Blk*SS*

iTrader: (4)

my rear end is narrowed 3" per side, The reason I did this was for a really deep dish. I was hoping 19x11 would fit, but is 19x10 the only option?

turbodarryl

iTrader: (4)

if u narrow ur rear 3'' per side then 19x11 deep dish should not be a problem, but u will need a BFH treatment or a mini tub. just my opinon

01Blk*SS*

iTrader: (4)

I understand I might need a BFH treatment, but I dont/cant mini tub at this time. That is why Im trying to research what fitment is best.

69TA

iTrader: (263)

here is my 305's
you don't need to do the BFH mod or mini tub

just need trailer mirrors to watch out for pedestrians when taking tight turns in the city



[/QUOTE]

69TA

iTrader: (263)

just kidding.
for real here is mine with 295's in 19's all around
you just need to roll the fender lips on the rears and
do nothing for the fronts

98CustomSS

iTrader: (3)

My rears are 19x11 they fit just fine.

01Blk*SS*

iTrader: (4)

Im going to run 19x11's and was hoping on 305's, my only dilema is that my rear end is narrowed 3" per side so im trying to figure out a backspacing that will yield the most clearance on the inner and outter part of the wheel. I tried using a wheel tool and came up with 4.5" backspacing for a 11" wide wheel. Im thinking of bringing the car to a wheel/tire store and asking if they can measure it for me. I wonder if they have this service???

Eskimo

iTrader: (9)

mine are 19x11, with an effective 50mm offset.. little bit of fender roll, little bit of BFH. Strano springs. 305/30 Michelin PS2's.

Sorry, no good rear 3/4 pics..

69TA

iTrader: (263)

5" w/ BFH mod
4.75" w/o

you can send me the money later

chaman

iTrader: (5)

Im running 275/30 all around and they seem beefy enough in the back.

Gohard

iTrader: (3)

Reminds me why I want custom wheels so bad. Sweet car man! 19x11 is perfection for the fbody

01Blk*SS*

iTrader: (4)

@ Eskimo, any possibility of you taking more pictures of the car? Im curious how much the wheel sits flush with outter fender lip.
thanks!

01Blk*SS*

iTrader: (4)

lol, thanks for your input. What is the backspacing on your wheels? also what brand tires are those? how do you like them? do you have a profile for your car?
thanks again.

69TA

iTrader: (263)

you talking about the 19's I am selling or
the ones on my other car?

01Blk*SS*

iTrader: (4)

the tires on the white trans am in the pictures you posted above.

01Blk*SS*

iTrader: (4)

So I did some measuring:
The wheels/tire size I would like is 19x11 with a 305/30/19. A nitto Invo that size has the following dimensions. 26.22" overall diameter and 12.36" width. I mocked that size tire up with the percy wheel tool and get a backspacing of a little less than 4.75". At the 4.75" backspacing, the 12.36" wide tire rubs a LOT on the inner fender. Since Its easier to roll the fenders to achieve more room on the outter fender well, I think the 4.5" backspacing would be better? correct me if Im wrong.

69TA

iTrader: (263)

these are the ones that i have for sale:

I am running 295's all around
wanted to be able to rotate the tires so kept it the same width all around

tires are 295/30ZR19 Michelin PS2 tires,
IMO they are the best tire for all around performance

only down side is that they cost a fortune.

Eskimo

iTrader: (9)

It's pretty flush - I honestly don't know how guys are running 12" wheels with lowered suspension unless they don't corner hard at all. I do, and it's 1/2 a turn on the PHB from rubbing the rolled fender lip, or rubbing the inner fender. The Michelin's are pretty wide though.

I do need to do another photoshoot before I put it up for winter, but I'm pretty busy for the next few weeks though.