New Amp Rack (Pics inside)
Thread Starter
Teching In
Joined: May 2003
Posts: 21
Likes: 0
From: Violetville, MD
New Amp Rack (Pics inside) Ive just installed my new amp rack. Im still awaiting the completiong of the acrylic covers which should be ready for pickup today.
Feel free to comment.
[image]http://images.fotopic.net/?id=791428&outx=600&oq=0[/image]
You can check out the rest at.
My Web Site
Feel free to comment.
[image]http://images.fotopic.net/?id=791428&outx=600&oq=0[/image]
You can check out the rest at.
My Web Site
Re: New Amp Rack (Pics inside) WonBadHawk, that is AWESOME. What is the air space per sub on your box? I need 1.5 cu ft per Solo D Series 15" sub I have. Could you send me the dimensions, and all the pics you have?
Thread Starter
Teching In
Joined: May 2003
Posts: 21
Likes: 0
From: Violetville, MD
Re: New Amp Rack (Pics inside) I have good news and bad news. The good news is I I went and picke dup the plastic this afternoon. 
the bad news is only one of the two pieces turned out, and its not completely right either. 
I gave the shop two pieces, of acrylic which were rough cut about 1 inch bigger on all sides to allow for final trimming later. One piece was longer then the other by about 3 inches, since one of the amps is 3 inches longer. I asked the guy to center the image on both pieces. Apparently he set the machine for the smaller one first and then used the same settings for the second sheet. So now Im gonna have to take in another sheet and have him redo it.
The smaller one turned out good, except the image is backwards. Most people wont realise it but those that do Im sure will ask why. Of course I could have reversed the plastic so the image was faceing the right direction but that would have put the engraved side face up, and It had a much nicer, cleaner appearance from the underside. Anyhow, I chose to go with what looked good versus what was graphical correct. Oh well...
Hopefuly I'll have the other sheet back soon.
Anyway, heres the pics. They dont show as well on camera, especially in doors but I wanted to get a few shots of it up so you all could take a peek.
[image]http://images.fotopic.net/?id=794230&outx=600&oq=0[/image]
The rest can be seen http:1badhawk.fotopic.net
the bad news is only one of the two pieces turned out, and its not completely right either. I gave the shop two pieces, of acrylic which were rough cut about 1 inch bigger on all sides to allow for final trimming later. One piece was longer then the other by about 3 inches, since one of the amps is 3 inches longer. I asked the guy to center the image on both pieces. Apparently he set the machine for the smaller one first and then used the same settings for the second sheet. So now Im gonna have to take in another sheet and have him redo it.
The smaller one turned out good, except the image is backwards. Most people wont realise it but those that do Im sure will ask why. Of course I could have reversed the plastic so the image was faceing the right direction but that would have put the engraved side face up, and It had a much nicer, cleaner appearance from the underside. Anyhow, I chose to go with what looked good versus what was graphical correct. Oh well...
Hopefuly I'll have the other sheet back soon.
Anyway, heres the pics. They dont show as well on camera, especially in doors but I wanted to get a few shots of it up so you all could take a peek.
[image]http://images.fotopic.net/?id=794230&outx=600&oq=0[/image]
The rest can be seen http:1badhawk.fotopic.net
