LS1TECH - Camaro and Firebird Forum Discussion
NEW PAN ALL UNITS ECEPT STOCK OR LOW BUDGET BUILDS
NEW PAN ALL UNITS ECEPT STOCK OR LOW BUDGET BUILDS
0 2023/09/04 15:31:03
0 2023/09/04 15:31:06
0 2023/09/04 15:31:08
0 2023/10/10 13:03:02
0 2023/10/10 15:21:32
0 2023/10/30 07:44:55
0 2023/11/21 16:07:17
0 2023/12/18 08:43:24
0 2024/01/02 18:24:03
0 2024/01/04 16:17:49
0 2024/03/19 06:55:15
0 2024/03/19 06:55:21
0 2024/03/19 06:55:24
0 2024/03/19 06:55:27
0 2024/03/19 06:55:30
0 2024/05/11 12:26:40
0 2024/05/17 13:03:12
0 2024/05/17 13:03:17
0 2024/05/17 13:03:20
0 2024/05/23 07:52:55
0 2024/06/10 08:12:21
0 2024/06/10 08:12:24
0 2024/06/10 08:12:27
LR piston in case
LR piston in case
0 2024/08/11 16:38:53
It is fine to install bushing from this side as long as this type case, The cases with the thicker back area must be done from front.
It is fine to install bushing from this side as long as this type case, The cases with the thicker back area must be done from front.
0 2024/08/11 16:38:35
Bushing installed should go in just uncovering the lube hole in case
Bushing installed should go in just uncovering the lube hole in case
0 2024/08/11 16:38:42
My extra special install tool.
My extra special install tool.
0 2024/08/11 16:38:59
Putting spring cage and clip in, Even if you are a first time builder this tool is IMO a must
Putting spring cage and clip in, Even if you are a first time builder this tool is IMO a must
0 2024/08/11 16:39:04
Rear LR piston with ne seals ready to install
Rear LR piston with ne seals ready to install
0 2024/08/11 16:38:47
This should spin freely in new bushing but have little if any side motion I prefer none.
This should spin freely in new bushing but have little if any side motion I prefer none.
0 2024/08/11 16:47:15
Planet installed make sure spinds freely and listen for unusual noise, Also note the gear race should be inspected carefully that nothing has been mashed in te splines the planet gears ride in, Most time easily removed but may make noise if missed.
Planet installed make sure spinds freely and listen for unusual noise, Also note the gear race should be inspected carefully that nothing has been mashed in te splines the planet gears ride in, Most time easily removed but may make noise if missed.
0 2024/08/11 16:47:32
Check planets for any wobble on every gear and end play should only be about .020, if you have any notable wobble on any gear or excessive endplay the planet most be replaced.
Check planets for any wobble on every gear and end play should only be about .020, if you have any notable wobble on any gear or excessive endplay the planet most be replaced.
0 2024/08/11 16:47:21
The little seal blade.(yes im old school still use one) is perfect for checking gear end play. it should just fit.
The little seal blade.(yes im old school still use one) is perfect for checking gear end play. it should just fit.
0 2024/08/11 16:47:27
I always use the stock anti clunk spring whenever possible at all, While I have used the case saver/savers they are not m,y preference due to the noise they make.
I always use the stock anti clunk spring whenever possible at all, While I have used the case saver/savers they are not m,y preference due to the noise they make.
0 2024/08/11 17:03:09
0 2024/08/11 17:03:03
I try and line up the oil grooves . Though it is not critical and the gap between the two busings will fill that duty.
I try and line up the oil grooves . Though it is not critical and the gap between the two busings will fill that duty.
0 2024/08/11 17:16:09
Nothes for oil sling to planets
Nothes for oil sling to planets
0 2024/08/11 17:16:43
Sunshell
Sunshell
0 2024/08/11 17:17:10
0 2024/08/11 17:30:10
I have a MM bushing installer set works well to remove and install its in 1mm increments
I have a MM bushing installer set works well to remove and install its in 1mm increments
0 2024/08/11 17:30:17