LS1TECH - Camaro and Firebird Forum Discussion
0 2017/05/05 10:04:44
0 2017/05/05 10:40:23
0 2017/05/10 15:29:02
Expansion tank is aluminum cylinder at the top of the firewall
Expansion tank is aluminum cylinder at the top of the firewall
0 2017/05/10 15:29:07
Tank reservoir is bottom right of the pic with the 2 bungs out the top
Tank reservoir is bottom right of the pic with the 2 bungs out the top
0 2017/05/10 15:29:13
0 2017/05/10 15:29:17
Bottom fitting feeds the pump below. Top will be return from the IC. I was going to run a line from the top to the expansion tank and a line from the expansion tank to the IC for air bleeding/filling. And plug the other 2.
Bottom fitting feeds the pump below. Top will be return from the IC. I was going to run a line from the top to the expansion tank and a line from the expansion tank to the IC for air bleeding/filling. And plug the other 2.
0 2017/05/10 15:29:22
0 2017/05/11 22:33:00
0 2017/05/11 22:33:06
0 2017/05/11 22:33:10
0 2017/05/11 22:33:17
Bleed fitting and rear IC return fitting. The plastic Tee is right to the bleed fitting. this is probably where I would tap for my one option with a shorter bit of hose of course.
Bleed fitting and rear IC return fitting. The plastic Tee is right to the bleed fitting. this is probably where I would tap for my one option with a shorter bit of hose of course.
0 2017/05/11 22:33:21
Bleed fitting line to top of expansion tank. Will run a line from the bottom to the reservoir but this would be its location.
Bleed fitting line to top of expansion tank. Will run a line from the bottom to the reservoir but this would be its location.
0 2017/05/11 22:33:26
0 2017/05/14 10:07:55
Going to look over the wires next.
Going to look over the wires next.
0 2017/05/14 10:08:01
That Tee is the highest point. Plus bc it's a hose I can just pull it up for easy filling and bleeding.
That Tee is the highest point. Plus bc it's a hose I can just pull it up for easy filling and bleeding.
0 2017/05/14 10:08:05
0 2017/05/15 19:44:07
0 2017/05/15 19:44:13
0 2017/05/15 19:44:18
0 2017/05/15 19:44:23
0 2017/05/15 19:44:28
0 2017/05/18 12:04:36
0 2017/05/18 12:04:37
0 2017/05/18 12:06:32
This is the 5 wire 02 included in the kit.
This is the 5 wire 02 included in the kit.
0 2017/08/16 21:02:16
LS1 on left and LS3 on the right
LS1 on left and LS3 on the right
0 2017/08/19 20:38:14
0 2017/09/14 17:49:03
0 2017/09/14 17:49:08
0 2017/09/14 18:00:13
0 2017/09/14 18:00:18
Grey oring is the original and the black at the base is the one I added.
Grey oring is the original and the black at the base is the one I added.
0 2017/09/14 19:19:58
Tabs that I later broke off, hole is enlarged here.
Tabs that I later broke off, hole is enlarged here.
0 2017/09/14 19:20:02
All done! Just need to fab up a Z bracket to keep her down for high boost!
All done! Just need to fab up a Z bracket to keep her down for high boost!
0 2017/09/14 19:20:05
0 2017/09/16 21:12:47
0 2017/09/16 21:18:37
0 2017/09/18 18:38:34
0 2017/09/18 18:38:38
0 2017/09/18 18:51:33
0 2017/09/18 18:51:37
Crossover to pass side
Crossover to pass side
0 2017/10/01 06:42:05