vatechguy3

iTrader: (4)

I have some problems with the fitment of my slp valance. had it painted and installed at the stealership. they messed with it for a few hours, and this is the best they could get it.

would like to get rid of the gaps on the front of both sides.

any ideas?

thanks
tony

vatechguy3

iTrader: (4)

left side pics.

tony

hlaalu

iTrader: (3)

take it back to the dealership if you payed them to put it on. looks like they need to clean up the ends a bit and redo that screw that looks way to low.

6LITEREATER

iTrader: (56)

That looks really odd... If anything the valance should be a little long on each side (that's how it came from SLP and that's how we molded ours) not a little short.

You shouldn't even have screws there. It should use just the factory body pins that are on the bumper.

vatechguy3

iTrader: (4)

so at this point, is there something i can do to fix it, or do i need to replace it?

thanks
tony

6LITEREATER

iTrader: (56)

I wouldn't replace it, doesn't look that bad...

I think if you took it back off and had it mounted a little higher it would fit better.

johnzss

iTrader: (11)

Yeah, take it back to the shop and have them refit it. Are these the SLP valance? or the 6le version? Im getting mine installed in a few days, i hope it turns out ok. GL

6LITEREATER

iTrader: (56)

I am 99% sure it is not a 6LE valance (at least not a current one, from like July+) as we have more material on the valance ends...

midnightblue02

iTrader: (21)

i bought an aftermarket one, but not the 6le one, it was the people who sold them before him and no not slp, but anyways mine looks like **** compared to that one. i would be happy if mine fit like yours, but i still understand what your saying.

whytryz28

iTrader: (28)

Best side picture I have, I dont think that is an SLP valence, because it is thicker than mine, unless SLP had 2 different molds or something.



Here is where it it supposed to be attatched, not with a screw like they did on yours.

whytryz28

iTrader: (28)

I bet they put it way to high at the center of the rear bumper, move it lower and the ends will move up and have enough length to fit properly.

Get pictures of the whole valance please.

6SSPEED

^^^^^ +1

'02SOMz28

iTrader: (1)

mmm mine fits kinda the same way and drive me insane!!!!!! mine has a little bit of a gap then this one though

slo_lt1

iTrader: (2)

i want a CME so bad,to damn expensive though. honestly if i was walking by your car i wouldn't notice it.

fatmat80

i have a 6liter dual exit stlyle fits god exept on one side, little too long. removed mine thinking about blending it to bumper. Can 6 liter shed light on how to fix fitment issue. not trynin to hijack...

6LITEREATER

iTrader: (56)

^^Urethane or fiberglass version?

vatechguy3

iTrader: (4)

mine is an slp, bought it used.

wish i would have waited till 6liter got his done.

mine also bolts up from the bottom of the valance. i think the dealer put the screw in to try and hold the front up to the bumper.
took it back and twice and got told to basically pound salt and since i didn't buy the part from them, they didn't have to make it fit perfect.

typical dealer.

the fit is definitely annoying. and i want to get 6liter rear splash guards, but i'm afriad they won't fit right because of the valance problem.

tony

6LITEREATER

iTrader: (56)

The splash guards have some play in how you mount them so it wouldn't be a problem...