4l60e won't shift out of 3rd gear
#1
Launching!
Thread Starter
iTrader: (8)
Join Date: Apr 2008
Posts: 200
Likes: 0
Received 0 Likes
on
0 Posts
4l60e won't shift out of 3rd gear
Rebuilt engine and trans and have about 140 miles on each. Was dyno tuned and ran fine except that the car would not idle when it was cold, as soon as it warmed up it ran great, no surge and good idle and shifted great. I was out driving tonight and the SES light came on and the trans would not shift our of 3 gear. It starts from a dead stop in 3rd and won't shift out of it. Got any ideas. Is my new trans shot?
#3
Rebuilt engine and trans and have about 140 miles on each. Was dyno tuned and ran fine except that the car would not idle when it was cold, as soon as it warmed up it ran great, no surge and good idle and shifted great. I was out driving tonight and the SES light came on and the trans would not shift our of 3 gear. It starts from a dead stop in 3rd and won't shift out of it. Got any ideas. Is my new trans shot?
__________________
https://ls1tech.com/forums/image.php...ine=1194732633
Free Cooler, Free shipping always, 2 year warranty Trans/Coverter combos, No Core or Core charge, $150 LS1 core buy back, All trans Dyno Tested to Be sure it works when you get it.Customer videos, Tech Thread, Open 7 Days a Week! Call or http://opi.yahoo.com/online?u=performabuilt&m=g&t=2Click Banner for Website.
Not Just Built.....PerformaBuilt!
https://ls1tech.com/forums/image.php...ine=1194732633
Free Cooler, Free shipping always, 2 year warranty Trans/Coverter combos, No Core or Core charge, $150 LS1 core buy back, All trans Dyno Tested to Be sure it works when you get it.Customer videos, Tech Thread, Open 7 Days a Week! Call or http://opi.yahoo.com/online?u=performabuilt&m=g&t=2Click Banner for Website.
Not Just Built.....PerformaBuilt!
#4
Launching!
Thread Starter
iTrader: (8)
Join Date: Apr 2008
Posts: 200
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the info. I am running a vig converter and it's around 3600 stall.I check the fuses and plugs (where are the fuses located) , if that's not it I'll reset it and get a code and drive it over to my friend shop tomorrow to see what code it's throwing.
#5
TECH Enthusiast
iTrader: (3)
Join Date: Oct 2006
Location: Idaho
Posts: 540
Likes: 0
Received 0 Likes
on
0 Posts
^Are you running a trans cooler for that higher stall? It could just be getting hot and the computer is going to limp mode to be safe. It feels the tranny is in danger. So it engages into 3rd, pulls timing, and adjusts line pressure to save it. Shut it off, let it cool down, sometimes this works, although your SES light will still be on.
My car does the same thing, but i also don't have a tune. Code may be 0757. Shift solenoid "B" Stuck on. If you aren't running a cooler, i highly advise getting one. And also it wont hurt anything, just don't rod it and stay at a cruising speed.
My car does the same thing, but i also don't have a tune. Code may be 0757. Shift solenoid "B" Stuck on. If you aren't running a cooler, i highly advise getting one. And also it wont hurt anything, just don't rod it and stay at a cruising speed.
#7
TECH Fanatic
iTrader: (1)
Join Date: Jul 2003
Location: edison, nj
Posts: 1,095
Likes: 0
Received 0 Likes
on
0 Posts
you just need that code shut off, it relates to excessive slip from the torque converter. The computer thinks that the stock converter is in there and its slipping too much which puts it out of the programmed threshold of what is acceptable amount of slip. Since you change the converer it slips a ton more than a stock one would hence limp mode. Simple to fix it, just have the code shut off and you will be good to go.
Trending Topics
#8
Sorry to bring this up from the dead but I am having the same problem. I have PO757 as well and about 50% of the time I am stuck in 3rd gear. There is a 50/50 chance it seems like that when I start the car it will be perfectly fine, or it will be stuck in 3 gear. I have a 3800 VIG stall with no tranny cooler.
I was planning on replacing the A and B shift solenoids and the harness ($55 in parts). Also I have heard varying opinions on just turning the code off.
I have been driving around in D and have had no issues so far. Anyone know why this is?
I was planning on replacing the A and B shift solenoids and the harness ($55 in parts). Also I have heard varying opinions on just turning the code off.
I have been driving around in D and have had no issues so far. Anyone know why this is?
#12
Code comes and goes when I am in OD. Transmission will be stuck in 3rd about 50% of the time (sometimes simply restarting the car will make it work like normal). If I keep it in D, then I have no issues.
#16
Mine has been doing the same thing for the last couple years. Shutting the car off for 20 or 30 seconds, then restarting it, has always resulted in the tranny resuming proper operation......so far.
#17
im having a similar issue i have a 99 gmc sierra 1500 4.8l 4x4. Was just shifting hard going from 1-2 but now i was riding around tonight and it stuck in 3rd gear any help would be great trans has 10k on it
also im getting low voltage code on all my coil packs and they r brand new coil and plug wires and plugs
also im getting low voltage code on all my coil packs and they r brand new coil and plug wires and plugs
#19
im having a similar issue i have a 99 gmc sierra 1500 4.8l 4x4. Was just shifting hard going from 1-2 but now i was riding around tonight and it stuck in 3rd gear any help would be great trans has 10k on it
also im getting low voltage code on all my coil packs and they r brand new coil and plug wires and plugs
also im getting low voltage code on all my coil packs and they r brand new coil and plug wires and plugs