Biggest number retaining the TVS1900???
#1
TECH Veteran
Thread Starter
Join Date: Sep 2003
Location: Las Vegas, NV
Posts: 4,540
Likes: 0
Received 0 Likes
on
0 Posts
Biggest number retaining the TVS1900???
We're slowly upgrading a 2010 Cadillac CTS-V for a customer at work. Today with the last bit of mods we hit 605RWHP and 618RWTQ. Next mod is a TVS2300 for an LS9. I'm just curious what is the biggest number from someone with an LSA that still has the TVS1900. I'm going to post the dyno sheets in just a bit showing the current numbers as well as the stock dyno numbers. I just need to get everything scanned.
#3
We did a smaller upper pulley 2.55. Hard air tube with factory replacement K&N. LSA re-worked heads and a LS9 camshaft. Innovators West lower with Metco ring. 1 7/8" LT's with a Corsa. Fastlane's large heat exchanger. Stock auto trans and NO convertor.
PS: Our DA at the time of the run was 5500++ft
Car is strong.
This is the LEP Stage III. Customer want's to do the LS9 ZR1 2300 blower. I will post the results from that as soon as we finish it up. I love this car!
Video
http://www.youtube.com/user/dragstri.../0/O4Xh0O6LRlM
Garth
Last edited by VegasLSX; 09-03-2010 at 11:41 PM.
#4
#5
Banned
iTrader: (11)
Join Date: Aug 2004
Location: Memphis
Posts: 541
Likes: 0
Received 0 Likes
on
0 Posts
It was posted on another forum.
What size metco ring are you running? Do you have a graph you can post with boost logged? I would get the fuel in check before jumping to a 2300 just to see what you can get out of each setup. Do you plan to run a ls9 blower or a magnuson kit?
What size metco ring are you running? Do you have a graph you can post with boost logged? I would get the fuel in check before jumping to a 2300 just to see what you can get out of each setup. Do you plan to run a ls9 blower or a magnuson kit?
#6
It was posted on another forum.
What size metco ring are you running? Do you have a graph you can post with boost logged? I would get the fuel in check before jumping to a 2300 just to see what you can get out of each setup. Do you plan to run a ls9 blower or a magnuson kit?
What size metco ring are you running? Do you have a graph you can post with boost logged? I would get the fuel in check before jumping to a 2300 just to see what you can get out of each setup. Do you plan to run a ls9 blower or a magnuson kit?
Is your car a Auto?
We made 525whp with just a upper STG I
(stock everything else)
700 whp soon???
Last edited by VegasLSX; 09-04-2010 at 10:02 AM.
#7
Make sure you get the Lingenfelter LS9 SC inlet manifold for that R2300, the stock LS9 SC inlet becomes very restrictive at SC speeds higher than stock.
http://www.lingenfelter.com/mm5/merc...egory_Code=C68
http://www.lingenfelter.com/mm5/merc...egory_Code=C68
Trending Topics
#8
Make sure you get the Lingenfelter LS9 SC inlet manifold for that R2300, the stock LS9 SC inlet becomes very restrictive at SC speeds higher than stock.
http://www.lingenfelter.com/mm5/merc...egory_Code=C68
http://www.lingenfelter.com/mm5/merc...egory_Code=C68