Starter Flange Broke & Cracked my Block
#1
On The Tree
Thread Starter
iTrader: (2)
Join Date: Apr 2009
Location: Michigan
Posts: 178
Likes: 0
Received 0 Likes
on
0 Posts
Starter Flange Broke & Cracked my Block
Hey all,
So basically had a mess the day I fired up my Rig. 98 LS1 in a Jeep Wrangler, see sig for more details.
First few times I cranked her over, I chipped two teeth on my flex plate
(The cheap, stamped plate, with the welded on ring)
For some reason I led myself to believe it would be ok for a little while, so tried starting the motor a few more times... dumb decision.
The motor fired up, then I shut it down... the next time I went to start it, I heard a loud noise from the starter/flexplate area... Got under there, and my starter flange had cracked in half completly and low and behold the outter tapped hole in my block for the starter bolt cracked.
It didnt crack completely, but bad enough to be concerned about. I dont think the crack traveled to the threads portion of the starter bolt hole... So I am wondering how to fix this/work around it without pulling the motor out.
Option 1:
There are a few starters on the market which have 3 & 4 bolt hole configurations, so I am thinking about just tapping 1 or 2 new holes in the block.
Option 2:
Get the cracked hole welded and re-tap it, thing is I imagine it being hard to weld aluminum on your back looking up.. not sure though
Option 3:
Design some kind of adapter flange that mates with my new starter and block, and try to get creative with tapping 1 or 2 new hole locations.
Anyone have any suggestions, input or ideas?
I will be purchasing the better flexplate this time around, im not sure if my old one was not heat treated properly, possibly bent... no clue
Thanks for any input you may have!
So basically had a mess the day I fired up my Rig. 98 LS1 in a Jeep Wrangler, see sig for more details.
First few times I cranked her over, I chipped two teeth on my flex plate
(The cheap, stamped plate, with the welded on ring)
For some reason I led myself to believe it would be ok for a little while, so tried starting the motor a few more times... dumb decision.
The motor fired up, then I shut it down... the next time I went to start it, I heard a loud noise from the starter/flexplate area... Got under there, and my starter flange had cracked in half completly and low and behold the outter tapped hole in my block for the starter bolt cracked.
It didnt crack completely, but bad enough to be concerned about. I dont think the crack traveled to the threads portion of the starter bolt hole... So I am wondering how to fix this/work around it without pulling the motor out.
Option 1:
There are a few starters on the market which have 3 & 4 bolt hole configurations, so I am thinking about just tapping 1 or 2 new holes in the block.
Option 2:
Get the cracked hole welded and re-tap it, thing is I imagine it being hard to weld aluminum on your back looking up.. not sure though
Option 3:
Design some kind of adapter flange that mates with my new starter and block, and try to get creative with tapping 1 or 2 new hole locations.
Anyone have any suggestions, input or ideas?
I will be purchasing the better flexplate this time around, im not sure if my old one was not heat treated properly, possibly bent... no clue
Thanks for any input you may have!
#5
Bczz
BCZZ
I recently seen your build thread. Very nice . I do have one question though. Why didn't you mock everything engine swapwise before you had the frame poweredcoated? I want the factory (low) AC mount too, but I don't think I could cut into a fresh poweredcoated frame. Just curious.
thanks,
Jim
I recently seen your build thread. Very nice . I do have one question though. Why didn't you mock everything engine swapwise before you had the frame poweredcoated? I want the factory (low) AC mount too, but I don't think I could cut into a fresh poweredcoated frame. Just curious.
thanks,
Jim
Trending Topics
#8
TECH Senior Member
iTrader: (12)
People have successfully welded iron block too.. but I would leave any of this to the so called experts..
Jimbo.. to answer the question, it started out as SBC build a long long time ago.. I was about to finish up the build and start to rebuild one of the SBC for it.. then one night sitting around with a few buddy's.. over a few too many.. got to BS'ing around and this and that.. and that would be cool and yeah you can do it.. and what ever else I can't remember.. well after the usual morning fun.
I was reseaching on LS1Tech.. and browsing Craigslists looking for pull out LS1, a few day later.. well you know the end to this story LOL!..
But atlease it was only the Notch for the AC Compressor that needed a touch up with paint and dosen't look to bad as you can't see too much of the patching..
BC
Jimbo.. to answer the question, it started out as SBC build a long long time ago.. I was about to finish up the build and start to rebuild one of the SBC for it.. then one night sitting around with a few buddy's.. over a few too many.. got to BS'ing around and this and that.. and that would be cool and yeah you can do it.. and what ever else I can't remember.. well after the usual morning fun.
I was reseaching on LS1Tech.. and browsing Craigslists looking for pull out LS1, a few day later.. well you know the end to this story LOL!..
But atlease it was only the Notch for the AC Compressor that needed a touch up with paint and dosen't look to bad as you can't see too much of the patching..
BC
Last edited by bczee; 04-15-2010 at 01:09 AM.
#10
On The Tree
Thread Starter
iTrader: (2)
Join Date: Apr 2009
Location: Michigan
Posts: 178
Likes: 0
Received 0 Likes
on
0 Posts
thanks for the suggestions, i'll get some pics up of it, sounds like its going to get welded. I have a ton of room under there, wonder if it can be welded in the jeep... then it wouldnt be a big deal at all.
#12
Launching!
iTrader: (1)
Hey all,
So basically had a mess the day I fired up my Rig. 98 LS1 in a Jeep Wrangler, see sig for more details.
First few times I cranked her over, I chipped two teeth on my flex plate
(The cheap, stamped plate, with the welded on ring)
For some reason I led myself to believe it would be ok for a little while, so tried starting the motor a few more times... dumb decision.
So basically had a mess the day I fired up my Rig. 98 LS1 in a Jeep Wrangler, see sig for more details.
First few times I cranked her over, I chipped two teeth on my flex plate
(The cheap, stamped plate, with the welded on ring)
For some reason I led myself to believe it would be ok for a little while, so tried starting the motor a few more times... dumb decision.
Don't try to short-cut the repair, do it the right way, don't make another "dumb decision", you see where the first one got ya.
#13
While the engine is out make sure you properly shim the starter before you mate the trans to the engine. My guess is there wasn't sufficient clearance for the starter gear.
This install guide shows one way to do it.
http://www.msdignition.com/instructi...?terms=starter
This install guide shows one way to do it.
http://www.msdignition.com/instructi...?terms=starter
#14
On The Tree
Thread Starter
iTrader: (2)
Join Date: Apr 2009
Location: Michigan
Posts: 178
Likes: 0
Received 0 Likes
on
0 Posts
Since the flexplate has broken teeth, you need to pull the engine or trans to replace it, might as well pull the engine so you can kill 2 birds with one stone. Repair the block properly and replace the broken flexplate.
Don't try to short-cut the repair, do it the right way, don't make another "dumb decision", you see where the first one got ya.
Don't try to short-cut the repair, do it the right way, don't make another "dumb decision", you see where the first one got ya.
While the engine is out make sure you properly shim the starter before you mate the trans to the engine. My guess is there wasn't sufficient clearance for the starter gear.
This install guide shows one way to do it.
http://www.msdignition.com/instructi...?terms=starter
This install guide shows one way to do it.
http://www.msdignition.com/instructi...?terms=starter
#15
On The Tree
Join Date: Jan 2007
Location: perryton tx
Posts: 130
Likes: 0
Received 0 Likes
on
0 Posts
should be able to get a tig torch in there. break it off all the way and weld it back on otherwise it could keep cracking and chasing cracks sucks. then helicoil it
#17
TECH Apprentice
#20
TECH Enthusiast
iTrader: (4)
Join Date: Jun 2003
Location: MS
Posts: 551
Likes: 0
Received 0 Likes
on
0 Posts
The reason I asked is because normally that's what happens if you try to start the car with a weak battery the starter will attempt to turn and then kick back and snap the mount on the block, thats what happened when I mine broke. The thin arm on the stock starter will break in some cases too. You can go back with a truck starter that has a thick flange on both sides, this will provide more support to the starter.
Last edited by SuperC1; 08-11-2011 at 01:06 PM.