tr_racing

iTrader: (1)

Which Catback exhaust(size & brands) is the best on a 240sx S14 with a LS1??????


Thanks!

Kevin..

soon2brb240

iTrader: (1)

Any of the good turbo cat back exhausts would be good. They're all 3" or over, so its about the same as an aftermarket f-body exhaust in size.

cnichols

iTrader: (23)

The Apex'i GT Spec is 3" to the resonator, but after the resonator, it jumps to 95mm (~3.75 inches) the rest of the way.

What I'm using...sounds great.

LS240sx

iTrader: (12)

Running the APexi N1 3 inch with resonator

Shinsetsu

iTrader: (2)

Sound clips?!

Verz

iTrader: (21)

Custom exhaust with magnaflow muffler

owen v8litew8

not an S14 but on my FC3S rx7 I run dual 2.5" with summit racing shorty glasspack resonators on each side after an Xpipe crossover under the driveshaft, then out to the back of the car with more 2.5" pipes, no other mufflers and it sounds great, actually pretty quiet inside the car and it was very inexpensive to fab it up with a friend who welds.

GTOpowered240sx

iTrader: (1)

running a custom dual 3" inlet/ single 4" out muffler and a race 4" muffler at the rear. If I was to use a catback, it would have been the Apexi GT spec.

angelR

iTrader: (7)

Using the apexi gt spec that came on the roller rx7 fc3s that I swapped. Sounds good but loud and it was essentially free

cnichols

iTrader: (23)

http://www.youtube.com/watch?v=j10t3Og5T2w

Mine w/ Hinson Longtubes to a 3" Y to Apex'i GT Spec. Completely stock otherwise.

tr_racing

iTrader: (1)

You have the Hinson header for S14? Does they fit well????

Thanks!

Kevin..

Kamin

heres mine, 2 dynomax race mufflers (not glasspacks) and custom dual 2.5" side exit with H pipe. hooker shorty headers modified and smoothed.

http://www.youtube.com/watch?v=jb9vpn9MaN0

video doesnt do it justice, its a much crisper sound in person.

tr_racing

iTrader: (1)

Which header is the best to bought ? easiest to modify to a S chassis??????

sirdoc99

iTrader: (1)

Word is the GTO header is fairly easy to make fit.

lukem80

iTrader: (4)

I wanna run hinson headers.... 3 inch y pipe to an electric cut out then just run 3 inch pipe back and 2 quiet mufflers.. gonna try to incorporate the stock muffler for the sleeper look.

mikespeed95

iTrader: (1)

just have someone make a custom set of headers so they actually fit your application.

and be a man. long tubes, dual 3'', and flowmaster outlaws.

tr_racing

iTrader: (1)

How much can be cost me a set of custom header? Can you make me a set? Mike I still waiting your kit You can answer me via my e-mail!

Kevin..

tr_racing

iTrader: (1)

Does the Hinson headers fit great or they are **** to put in S14??????? Which headers will be the easiest to modify to fit in a S chassis?????

Thanks!!!

sirdoc99

iTrader: (1)

According to a member on here, all you need to do is mill the GTO headers and they fit. I'm debating if I just want to fab some long tubes myself.

mikespeed95

iTrader: (1)

email me again, i've been reall busy tryign to help get a car done for sema.