ls2 long block in my 2000 SS
#1
ls2 long block in my 2000 SS
just ran thru 12" of water in my dropped SS and hydro locked the motor. Getting insurance money 1st of next week. I can get a good deal on a LS2 long block out of a 05 C6 with less than 40K miles. Just going to cam it with rod and head bolts and some .040 cometics for some spray.
questions....
WILL MY LS6 INTAKE FIT?
WILL MY ACC. ALL FIT?
WHAT DO I NEED TO DO ABOUT MY RELUCTOR WHEEL?
ARP ROD BOLTS AND HEAD STUDS ENOUGH FOR THE 150 SHOT WITH A FRESH MILLED HEAD AND COMETIC GASKETS?
Anything else I need to consider if I'm going with the LS2?
I don't really want the weight of the LQ9 unless i'm going FI. Any help will be appreciated. I get my check soon so I need to make a decision.
questions....
WILL MY LS6 INTAKE FIT?
WILL MY ACC. ALL FIT?
WHAT DO I NEED TO DO ABOUT MY RELUCTOR WHEEL?
ARP ROD BOLTS AND HEAD STUDS ENOUGH FOR THE 150 SHOT WITH A FRESH MILLED HEAD AND COMETIC GASKETS?
Anything else I need to consider if I'm going with the LS2?
I don't really want the weight of the LQ9 unless i'm going FI. Any help will be appreciated. I get my check soon so I need to make a decision.
#4
TECH Veteran
iTrader: (14)
You will need a cam extension harness from katech along with a knock sensor harness extension because the new knock sensors will have to be drilled and tapped on the side of the block. The reluctor wheel as long as the block is an 05 should have a 24x reluctor wheel and to my knowledge ls2's in 06 also got them but be sure and check if it is a 58x you can buy a conversion box from katech also.
#6
katech knock sensor extension harness and cam angle sensor harness and bolt it up. The motor is out of an 05 C6.
#7
http://store.katechengines.com/cam--...rness-p18.aspx
This is all I need? Besides some bigger injecters and a walbro fuel pump? My 2000 LS1 came with 26lbers. I'm thinking some 36lbers and a walbro witha hard wire kit??
Now for the million$$ question.
WHAT CAM???
228R, Torquer V2, or oem LS6 cam??
I would like to just buy a used LS6 cam and save the valve spring money for my HSW wet kit. If not I will be doing the TSP single spring package with the PAC 1518's and a mild cam. TV2,228R, etc.
This is all I need? Besides some bigger injecters and a walbro fuel pump? My 2000 LS1 came with 26lbers. I'm thinking some 36lbers and a walbro witha hard wire kit??
Now for the million$$ question.
WHAT CAM???
228R, Torquer V2, or oem LS6 cam??
I would like to just buy a used LS6 cam and save the valve spring money for my HSW wet kit. If not I will be doing the TSP single spring package with the PAC 1518's and a mild cam. TV2,228R, etc.
Last edited by S13LSx; 06-21-2010 at 08:38 AM.
Trending Topics
#10
On The Tree
iTrader: (77)
Join Date: Oct 2008
Location: Rockwall, TX.
Posts: 179
Likes: 0
Received 0 Likes
on
0 Posts
You need 2 ls2 knock sensors,just bolt them to the oil pan bolts,its not hard to wire them yourself,the cam sensor a 3 wire.cant be too hard.you have to reverse the outside wires on the plug.and if its an early 05 model it is a 24 reluctor crank.i think if the crank sensor's black,its 24x,if its grey its 58x,or vise versa?