CMS is the Shiznit!
03-13-2011, 01:50 AM
#1
11 Second Club
Thread Starter
iTrader: (15)
Join Date: Mar 2007
Location: So Cal
Posts: 772
Likes: 0
Received 0 Likes
on
0 Posts
CMS is the Shiznit! Ryne took 3-4 hours tweaking on my car because I did a few new mods. He was able to get my idle and crusing tune dialed in great. He stayed at the shop till 830 pm making sure he had my car just right and changed my tune to Speed Density. We did some runs and I was able to pick up some nice gains. I'm very happy with his tuning and I am super stoked my car runs as good as it does.
I replaced my MS3 cam with a 247/251. I also added bigger headers and ported my FAST 92.
The picture below shows a comparison to the last time I was there and got my car dynoed.
I'll be getting some 4.10's installed by CMS very soon and then its off to the track to she what she will do.
I replaced my MS3 cam with a 247/251. I also added bigger headers and ported my FAST 92.
The picture below shows a comparison to the last time I was there and got my car dynoed.
I'll be getting some 4.10's installed by CMS very soon and then its off to the track to she what she will do.
03-13-2011, 02:51 PM
#4
11 Second Club
Thread Starter
iTrader: (15)
Join Date: Mar 2007
Location: So Cal
Posts: 772
Likes: 0
Received 0 Likes
on
0 Posts
I'm also trying to get some skinnies for the front so it might be a little bit before I get out to the track. On a side note I just realised I made 50 RWHP & 35 RWTQ more at 6400
Last edited by Fifedogg; 03-13-2011 at 02:56 PM.
03-14-2011, 12:04 AM
#7
I want to put the gears in first as I want to make it count because I get kicked out 1st run I'm also trying to get some skinnies for the front so it might be a little bit before I get out to the track.
On a side note I just realised I made 50 RWHP & 35 RWTQ more at 6400
I'm also trying to get some skinnies for the front so it might be a little bit before I get out to the track. On a side note I just realised I made 50 RWHP & 35 RWTQ more at 6400
Trending Topics
03-15-2011, 12:09 PM
#9
LS1TECH Sponsor
Join Date: Nov 2007
Posts: 16
Likes: 0
Received 0 Likes
on
0 Posts
I can't wait to get my motor finished.
03-18-2011, 05:47 PM
#17
Gotcha! I went off of your newest dyno sheet, my bad.
I've got a 402 with AFR 72cc 230v2's (milled to 67), a ported 102/102/104 combo, and a cam that is still being spec'd (but similar to yours). I'm shooting to have this baby in in a month and a half or so...... or as soon as I start working again, lol.
If you're free tonight, swing out to Bob's in Burbank tonight so I can hear that thing!
I've got a 402 with AFR 72cc 230v2's (milled to 67), a ported 102/102/104 combo, and a cam that is still being spec'd (but similar to yours). I'm shooting to have this baby in in a month and a half or so...... or as soon as I start working again, lol.
If you're free tonight, swing out to Bob's in Burbank tonight so I can hear that thing!
