Race car part out....
06-10-2012, 06:55 AM
#1
TECH Junkie
Thread Starter
iTrader: (10)
Join Date: Nov 2002
Location: Deerfield Beach, FL
Posts: 3,672
Likes: 0
Received 0 Likes
on
0 Posts
Race car part out.... Category: Racing Parts
Price: $0
Part Fits: 93-02 Chevrolet Camaro, 93-02 Pontiac Firebird
Location (State): FL
Item Condition: Used
Shipping Information: Item Can be Shipped
Engine: LS1/LS6
LS Engine?: Fits LS Engine
Midwest Chassis fab 9" and rear suspension, here's the parts list -
MWC housing narrowed 4" per side w/ 40 spline ends
Short arm torque arm
Back Brace
Transverse shock mounts
Black powder coating
Strange ultra case 3.812 package for large stem
Strange pro race 40 spline gun drilled axles 3.350 brg 5/8 studs
Strange pro race lightweight spool
3.50 pro gear
9" yoke 35spl 1350 strange chrome-moly
Strange brake mounting plates
Pan hard bar double adjustable
Anti roll bar
I paid $46xx for all of that and it's all brand new, installed in the car and has been sitting there unused since. I'll knock $1000 off it and there's no wait time (I waited 8 - 10 months to get it from Midwest). So $3600 and i'd be willing to meet up with you for delivery within an hour of port saint lucie florida, otherwise buyer pays shipping. I'll also throw in my madman double adjustable lca's that were already on the car to complete the rear suspension.
Powerglide - JW Case and Bellhousing, has all TSI internals to spec of the proline 5000 model, nasa input shaft, 1.80 first gear planetary set, pro mod drum, etc. Ready to handle a lot of power, only has 6 passes on it. Also have FTI SSW 4400 nitrous converter. Trans and Converter ran me over $4000, would like to get $2800 for both or $2500 for the trans and $500 for the converter if they're seperated.
Full set of QA1's - Front qa1's with 275 lb springs and rear qa1's complete set $400 (that's about half price of buying it all new)
Weld Draglites - Fronts 15x3.5 w/ 165r15 radials on them and Rears 15x10 w/3.5" bs and Mickey 275/60-15 radials on them. Looking for $500 for the entire set, or $275 fronts and $400 rears.
'99 Z28 body with 10 pt chromemoly cage - Cage was over $2000, $1000 takes it.
2003 5.3l truck shortblock w/80k miles on it - Ring gap opened up for boost, has arp rod bolts in it, cleaned up and ready to go. $500 takes it
AEM injector driver -Driver has very little use (loaned it to a friend after I bought it for a short amount of time). $175
Buyer is to pay shipping costs, accept paypal or check.
06-10-2012, 07:58 AM
#4
TECH Junkie
Thread Starter
iTrader: (10)
Join Date: Nov 2002
Location: Deerfield Beach, FL
Posts: 3,672
Likes: 0
Received 0 Likes
on
0 Posts
The rears will only fit with a rearend narrowed 4" per side. Also, id like the big stuff (rear and trans) to go before I sell the little ****. If the big stuff doesnt go im not making it unmoveable in my garage for a few hundred dollars on the little ****.
06-10-2012, 10:09 AM
#7
TECH Junkie
Thread Starter
iTrader: (10)
Join Date: Nov 2002
Location: Deerfield Beach, FL
Posts: 3,672
Likes: 0
Received 0 Likes
on
0 Posts
A local race shop had the tranny built for me, not sure who they use, but I think its ATF (Automatic Transmission Factory) in Davie, FL. Its got a tsi pro brake in it and this was behind a 374 cube ls1 with a 300 shot. Only put 6 1/8 mile hits on it after swapping from a th400. Car went 5.72 @ 122 & a best 60' of 1.28 when I kept the hit soft and kept it ogf the bumper. Car has a stock kmember.
Trending Topics
06-11-2012, 06:18 AM
#12
TECH Junkie
Thread Starter
iTrader: (10)
Join Date: Nov 2002
Location: Deerfield Beach, FL
Posts: 3,672
Likes: 0
Received 0 Likes
on
0 Posts
Pics of 1999 Z28 j3backer@mchsi.com and what tires and rearend would come with it to transport?
If you were taking just the body, you'd have to bring a rear and tires, I dont have anything to put back in it.
06-12-2012, 07:53 PM
#14
TECH Junkie
Thread Starter
iTrader: (10)
Join Date: Nov 2002
Location: Deerfield Beach, FL
Posts: 3,672
Likes: 0
Received 0 Likes
on
0 Posts
Sorry, haven't had a chance to get on here, been busy as hell at work, but I just replied to all pm's.
I have a possible sale on the roller as a whole, so I will let you guys know if it falls through or not, thanks.
I have a possible sale on the roller as a whole, so I will let you guys know if it falls through or not, thanks.
