I LOVE my MAC's ... anybody who doesn't?
12-18-2004, 07:12 PM
#1
I LOVE my MAC's ... anybody who doesn't? MAC CATS seem to suck, so, we're speaking of ORY, not the MAC CATS.
It seems like most of the older and experienced folks here who have owned numerous sets of LT's and MAC's, well, it seems to be a general consensus that they feel the 1 3/4" mid-length MAC's and ORY performed pretty much as well and sometimes better than LT's ... when ported properly. Would you agree or do you think MAC's suck? I LOVE my MAC's!!!!!
It seems like most of the older and experienced folks here who have owned numerous sets of LT's and MAC's, well, it seems to be a general consensus that they feel the 1 3/4" mid-length MAC's and ORY performed pretty much as well and sometimes better than LT's ... when ported properly. Would you agree or do you think MAC's suck? I LOVE my MAC's!!!!!
12-19-2004, 12:07 AM
#5
Originally Posted by JEB99TA
I LOVE my MAC's ... anybody who doesn't?
I might actually like my own Macs though if I were to put them on the car but for now they're sitting in a box in my living room.
Decent headers for sure but I think I'm going with QTPs instead. 
12-19-2004, 12:10 AM
#6
On The Tree
Join Date: Oct 2004
Posts: 164
Likes: 0
Received 0 Likes
on
0 Posts
my used ones that i put on with oryp... well i sprayed them with coating and all the goods.. ported the primaires out as nice as ive seen anyone else do, and well i just cant feel any gain thru the catback or cutout.. i guess this is becuase i spun before anywhere in 1st or low second and i spin now so hard to say..
Trending Topics
12-19-2004, 01:00 AM
#8
10 Second Club
iTrader: (15)
Join Date: Nov 2001
Location: St. Michael, MN.
Posts: 4,519
Likes: 0
Received 0 Likes
on
0 Posts
Mine sounded much better after I had a Flowmaster Y welded into the Y. Gave it more of a tuned sound and less rasp. However I will be changing my engine setup and switch to 1-7/8" LT's.
12-19-2004, 03:23 AM
#9
On The Tree
Join Date: Oct 2004
Posts: 164
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by DrkPhx
Mine sounded much better after I had a Flowmaster Y welded into the Y. Gave it more of a tuned sound and less rasp. However I will be changing my engine setup and switch to 1-7/8" LT's.
mmkay what exactly did u do now?? id prolly keep my mac mids but wouldnt' mind upgrading to a less raspy y pipe... did u just leave teh mac y bolted up to the headers for about 6 inches and then replace it from there back or did u weld the y to the headers??
12-19-2004, 08:25 AM
#10
TECH Senior Member
I like my MACs too.
Question, has any one done duals with X pipe on MACs??
If so any pics?
'm thinking of doing that and I could use illustrations so I can see where to position the X pipe and mufflers etc... Oh BTW was thinking Spintech muffs, what do you think?
Question, has any one done duals with X pipe on MACs??
If so any pics?
'm thinking of doing that and I could use illustrations so I can see where to position the X pipe and mufflers etc... Oh BTW was thinking Spintech muffs, what do you think?
12-19-2004, 02:14 PM
#11
10 Second Club
iTrader: (15)
Join Date: Nov 2001
Location: St. Michael, MN.
Posts: 4,519
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by redrocketls1
mmkay what exactly did u do now?? id prolly keep my mac mids but wouldnt' mind upgrading to a less raspy y pipe... did u just leave teh mac y bolted up to the headers for about 6 inches and then replace it from there back or did u weld the y to the headers??
