Looking at DynoTune kit
03-31-2006, 08:05 PM
#1
12 Second Club
Thread Starter
iTrader: (1)
Join Date: Aug 2005
Location: Oneida, IL
Posts: 114
Likes: 0
Received 0 Likes
on
0 Posts
Looking at DynoTune kit Anyone who has installed DynoTune nitrous kits let me know what you think. I'm looking at getting the kit that is on sale for the LS1... I will also get the MSD window switch, fuel pressure safety switch, bottle heater, purge system w/ dual outlets, pressure guage and N20 filter... Could I possible need anything else?? Please let me know.
03-31-2006, 08:24 PM
#2
i have their purge and bottle warmer and i am very pleased they make great products and have great customer service- The msd window switch i did not have the best of luck with but i hope you do- for $110 more i would do it right and get an FJO
03-31-2006, 08:44 PM
#3
TECH Addict
iTrader: (21)
Join Date: Nov 2005
Location: Maine USA
Posts: 2,209
Likes: 0
Received 0 Likes
on
0 Posts
Got a dry kit from Dynotune also purchased their Bottle opener, Billet Bottle Bracket, Heater, Gauges, and Window Switch.
Still doing the install but so far everything is top notch!
Cheers
Beer
Still doing the install but so far everything is top notch!
Cheers
Beer
03-31-2006, 08:57 PM
#4
TECH Regular
iTrader: (18)
Join Date: Nov 2005
Location: Little Rock, AR
Posts: 412
Likes: 0
Received 0 Likes
on
0 Posts
Cant vouch for there actual kits but they do have top of the line customer service and speedy shipping! Never heard of anything bad with them and your setup sounds safe and strong. Good luck!
03-31-2006, 09:01 PM
#5
TECH Regular
iTrader: (18)
Join Date: Nov 2005
Location: Little Rock, AR
Posts: 412
Likes: 0
Received 0 Likes
on
0 Posts
Also I would go with their pressure adjustable bottle heater. Pressure adjustable is the best way to go imo. You turn it on and it stays on until you get to a set pressure and shuts off when you are there. When it goes down again (ex. after you spray) it turns back on. Safe and hassle free. The only thing you didnt mention was a remote opener which is all about preference. I dont have one now but I am on the verge of ordering one because I am lazy and dont like popping the hatch to turn it on or off lol.
04-01-2006, 03:08 PM
#7
TECH Fanatic
iTrader: (12)
Join Date: Feb 2004
Location: Mass
Posts: 1,600
Likes: 0
Received 0 Likes
on
0 Posts
I have one of their dry kits with access... and have had know issues.Very good quauilty and straight foward install and great directions.Plus the guys are great to deal with
BTLFEDSS
BTLFEDSS
Trending Topics
04-02-2006, 11:54 AM
#10
LS1TECH Sponsor
iTrader: (13)
Join Date: Jul 2004
Location: Massachusetts
Posts: 1,766
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by jocko
i'm glad i read this cause i'm about to order one since they're the cheapest,what issues are people having with the msd window switch?and is there another option to that switch?
Here is a great option the the MSD window switch - it not only does what the MSD does but also has the option for a second stage, has a built in TPS and also offers multi-gear lockout feature. Here are more details. ANd for only $30 more than the MSD you cant go wrong!
http://www.dynotunenitrous.com/store...?idproduct=194
Dean
04-02-2006, 02:22 PM
#11
Staging Lane
Join Date: Nov 2003
Posts: 90
Likes: 0
Received 0 Likes
on
0 Posts
hello dean,do i really need that one for a 6 speed car?is a vette,and do either one of the window switches have instructions?i don't know where to get rpm signal on the ls1?i would imagine from one of the coils but i'm not sure,i might be placing my order tonight so it would help if you can reply,thanks.
04-02-2006, 04:29 PM
#12
the pcm is located pass side in fender well, and you get to it by removing wheel and inner fender liner. it's the white #10 wire. You can see the numbers and only one has 10 and is white. There are two connectors you'll be looking at the red one. Some early cars use the #35 connector but likey this hole will be empty/not used on both of your connectors.
Robert
Robert
04-02-2006, 08:58 PM
#14
LS1TECH Sponsor
iTrader: (13)
Join Date: Jul 2004
Location: Massachusetts
Posts: 1,766
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by jocko
hello dean,do i really need that one for a 6 speed car?is a vette,and do either one of the window switches have instructions?i don't know where to get rpm signal on the ls1?i would imagine from one of the coils but i'm not sure,i might be placing my order tonight so it would help if you can reply,thanks.
Robert is right on with the wire. Instructions are included as well.
Dean
04-02-2006, 09:03 PM
#15
Staging Lane
Join Date: Dec 2001
Location: LaHabra ,CA
Posts: 53
Likes: 0
Received 0 Likes
on
0 Posts
I inquired about a kit for the C6 Corvette today(Sunday) via email and got a response the same day. Nice to know you can get answers on Sunday. I'll be calling them tomorrow to get further details about my kit.
Regards Doug
Regards Doug
04-03-2006, 07:44 AM
#18
LS1TECH Sponsor
iTrader: (13)
Join Date: Jul 2004
Location: Massachusetts
Posts: 1,766
Likes: 0
Received 0 Likes
on
0 Posts
Yes, 7 days a week is required quite often. There are only 5 of us and we do what it takes to make sure we are always able to help!
We feel we provide industry leading quality, innovation and customer service for a great price!
Thanks again guys for your business it is very much appreciated!
Dean
We feel we provide industry leading quality, innovation and customer service for a great price!
Thanks again guys for your business it is very much appreciated!
Dean
04-03-2006, 03:11 PM
#20
TECH Apprentice
iTrader: (1)
Join Date: Apr 2002
Location: Portland, OR
Posts: 377
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by DynotuneN2O
Yes, 7 days a week is required quite often. There are only 5 of us and we do what it takes to make sure we are always able to help!
We feel we provide industry leading quality, innovation and customer service for a great price!
Thanks again guys for your business it is very much appreciated!
Dean
We feel we provide industry leading quality, innovation and customer service for a great price!
Thanks again guys for your business it is very much appreciated!
Dean
Glad to see biz is doing so good.
Robert