what mods to get????
#7
10 Second Sleeper Club
iTrader: (4)
Join Date: Aug 2005
Location: Victoria, Texas
Posts: 237
Likes: 0
Received 0 Likes
on
0 Posts
Just look at the signature. There all there with the exception of the Fuddle 3400 torque converter getting dropped in next week. This will help lower 0-60 ft times as well as increase overall performance in the car on street or strip. If I had to do it all over again the Stall would be one of the first mods I would have done. No serious regrets about how i've done it though. Lid, Cold air induction, Bellows and MAf along with Magnaflo (love the sound) came first. Used a hand helt tuner that tied these mods together (Jet performance) Ran very low 13's(13.2-13.3) with this setup. The car litteraly just woke up and became Nasty. Then came the Pacesetter coated LT's with a Catted Y pipe from TSP followed by a tune (professional tune when adding headers and Y pipe a must). Handhelds will only take you so far. Goal is to build a low 12 or high 11 sec car with no cage as this is my daily driver. Tryin to do it with just bolt ons and the plan is working. Good luck! Come join us.
The times listed below occured on a very hot and humid Texas night with no slicks. Everybody was runnin shitty that night. Will be headed back in july to see what it does then. Less humidity I hope.
The times listed below occured on a very hot and humid Texas night with no slicks. Everybody was runnin shitty that night. Will be headed back in july to see what it does then. Less humidity I hope.
Trending Topics
#8
12 Second Club
iTrader: (1)
Join Date: Oct 2004
Location: Raleigh, NC
Posts: 280
Likes: 0
Received 0 Likes
on
0 Posts
Free mods, lid, cutout and tune got me this, on shitty Kumhos with a full tank of gas.
http://i5.photobucket.com/albums/y16...02z28/best.jpg
http://i5.photobucket.com/albums/y16...02z28/best.jpg
#9
Launching!
Thread Starter
iTrader: (6)
Join Date: Feb 2006
Location: Hazel Green,AL
Posts: 270
Likes: 0
Received 0 Likes
on
0 Posts
I have a 1/8 mile track where i live and the best i ran was a 8.6 but that was when it started geting a little cold all i had was a hooker catback. I have M6 so its hard to get it the same all the time. This summer the best was a crapy 9.0xxx and i had whats in my sig. I need a better launch my clutch will not hold up if i launch hard.
#10
'Bird Director
iTrader: (80)
Originally Posted by TRANSAM_2000
does anyone have a list of all the bolt-ons that i could do thanks?
#11
Launching!
Thread Starter
iTrader: (6)
Join Date: Feb 2006
Location: Hazel Green,AL
Posts: 270
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by y2k_ta
#12
11 Second Club
iTrader: (36)
Join Date: May 2005
Location: South Jerzy
Posts: 1,449
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by TRANSAM_2000
does anyone have a list of all the bolt-ons that i could do thanks?
everyone says with a LS6 intake and a tune, 2-3 tenths will be dropped
DR's 1-2 tenths
but before all the mods- 12.97@ 110 Lid, catback, spec stage 3 clutch and free mods. thats before i learned how to launch it on street tires..
I saw a 2002 WS6 with just a drop in K&N filter run a 12.98 @ 109
#14
11 Second Club
Originally Posted by TRANSAM_2000
I need a new clutch because I'm still running my stock one with 67,800 miles on it.
Good Luck.
#15
Originally Posted by 00cls1camaross
you need some sticky tires and lid, catback, ory, and headers
or maybe just sticky tires....
or maybe just sticky tires....