WhiteGXP313

I know its probably been beaten to death and i tried to search for it but gave up after awhile..... When i deleted the resonator and had the whole exhaust out from the cat it sounded mean but the DOD drone would prob be unbearable so where would be the best spot? any videos? I should be recieving it from summit on monday and i would love to put it on before the Woodward Dream cruise!!!

Hawkins04

iTrader: (4)

a lot of people put them in the downpipe

Tappeter

iTrader: (2)

I think if you look under the car, you will find that trying to put the exhaust cutout on the down pipe or where the resonator was, is going to be a difficult and tight fit. There is very little room either place and you don't want it hanging down too low and getting snagged on speed bumps etc. I put mine in the pipe just before the mufflers right next to the rear right wheel/tire. It was much easier and neater. Sounds great and keeps raw exhaust from getting into cabin of car. I did make a small turn down tip to aim exhaust down.

JWMayes

Ya, downpipe isn't the greatest idea from experience. Theres not enough room there, and the way I got mine on, was to angle it forward a bit. I will post pics when I redo my exhaust though, I am going move it to a different spot, so hopefully it works out better. Hopefully I get it done in the next few weeks.

Model16

After the resonator..The area where the exhaust tubing is about right under the rear passenger seat...I have mine there and love it because its very easy to get too, and I have the opening angled to the side and slightly down..

94ss06gxp

iTrader: (5)

Ill be at woodward, ill keep an eye out for a white GXP

ImpSS07

iTrader: (3)

I've got mine by the rear pass tire.




The DOD drone/chopper sounds are pretty awful, but when i've listened to it with the gear selector in 3rd it's hardly noticeable.

DP 08 GXP

iTrader: (3)

i had mine on the DP but it was tucked up pretty close to where the exhaust manifolds meet the DP....it was loud as ****.....if there was no wind when you came to a stop you could smell the exhaust a little bit but i didnt think it was too bad...as long as you didnt have the fans blowing...here is what it used to sound like

https://ls1tech.com/forums/ls4-perfo...aust-note.html

WhiteGXP313

first off i gotta say that summit racing shipping is fast i ordered the part on thursday night and received it saturday I ordered the manual one just for the dream cruise loll so the downpipe is out of the question even though DPs GXP sounded amazing. I think im going to put it

so its easy to get to. impss07 do you have a video of yours?

DavidGXP

iTrader: (14)

On my front door step!

94ss06gxp

iTrader: (5)

thats the same place i had mine, i could take it off and put it on without even laying on the ground.

ImpSS07

iTrader: (3)

Only one I have right now.

Turn your speakers down then adjust accordingly!!

http://www.youtube.com/watch?v=BKOgMIkIWPc

ImpSS07

iTrader: (3)

Mine is closer to the mufflers though. I wanted to put mine where you want yours but the solenoid on the e-cutout stuck out more than I liked.

WhiteGXP313

I installed it yesterday and its perfect. If you want a loud exhaust then this is the way to go. I received 3 compliments on it within the first 15 min one pulling into the gas station, one starting up the car to leave the gas station, then one from a group of kids at autozone. The install was VERY easy if you have the tools, only hitch was the cutout was exactly 2 1/4 dia. so i had to go to autozone and rent a tailpipe expander. The only thing that worries me is the cutout is about 5 inches away from the rear tire, but that is the only place it could go. Any harm in this? Ill post videos when i get a chance but i doubt they will do it justice.

hazards280

That sounds great man! I was at woodward as well and I think I saw your car. Cutout was closed though!

ghetto joe

so just for clarification the stock exhaust up to the "Y" for the mufflers is 2.5 inch OD right? im looking at the DMH Electric unit so i would want the 2.5inch correct? can anyone tell me if that will fit inside or outside or same size as stock exhaust?

ImpSS07

iTrader: (3)

Look at my pic above. Thats a DMH 2.5" cutout with their pipe. Just cut out the piece and weld in the pipe.

higsy

I put mine right where the pipe splits to go to both mufflers. Faces straight out the back in the middle of the car and is damn loud. Don't lose any height with the exhaust either.

Was alot of work grinding to fit but it was worth it.

spydog

will it sound louder with or without the resinator i want to install a electric cut out in the pic just before it splits ti the 2 mufflers

94ss06gxp

iTrader: (5)

it sounds awesome without the resonator. no rasp at all if you are still catted.