Track prepped bolt on VS street prepped cam'd
#1
TECH Addict
Thread Starter
iTrader: (1)
Join Date: Mar 2008
Posts: 2,351
Likes: 0
Received 0 Likes
on
0 Posts
Track prepped bolt on VS street prepped cam'd
As they were setup in the race both are around 12.9 cars.
http://www.youtube.com/watch?v=Lrtl7gHfduY
http://www.youtube.com/watch?v=Lrtl7gHfduY
#2
So your lt1 with a cam had a hard time pulling from a roll on a bolt on lt1? That's awesome if so. Good runs either way.
Last edited by white ghost; 05-05-2011 at 05:22 PM.
Trending Topics
#9
TECH Addict
Thread Starter
iTrader: (1)
Join Date: Mar 2008
Posts: 2,351
Likes: 0
Received 0 Likes
on
0 Posts
3400' DA + Street tires + cam + stall = 12.9ish.
Bolt ons car @2000' da with DRs ran 12.9
This made for an interesting race.
Had I ran my track tune and DRs the races would have been different. My car is not setup for roll racing so again this made for some interesting races.
#17
On The Tree
Join Date: May 2011
Location: Gilbert, Az
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
My set up..
Ported/Painted LT1 Intake
58mm BBK Throttle Body
Jet Hot Longtube Headers
Catless Y-Pipe
Corsa 3" Catback Exhaust w/cut-out
3.73 Gears
17" ZR1 Rear Rims w/ 275/40/17 nitto Drag Radials
Summit Electric Waterpump
OTVC MSD Wires w/NGK TR55 Plugs
MSD Opti Cap/Rotor
MSD Coil
GM AC Delete Pulley
Bmr Strut Bar Brace
Bmr Rear Lower Control Arms
Bmr Panhard Bar
Powerstop Drilled/Slotted Rotors
Dyno Tuned By Bryan Herter (PCMforless.com)
and Holy Water in the radiator.
Ported/Painted LT1 Intake
58mm BBK Throttle Body
Jet Hot Longtube Headers
Catless Y-Pipe
Corsa 3" Catback Exhaust w/cut-out
3.73 Gears
17" ZR1 Rear Rims w/ 275/40/17 nitto Drag Radials
Summit Electric Waterpump
OTVC MSD Wires w/NGK TR55 Plugs
MSD Opti Cap/Rotor
MSD Coil
GM AC Delete Pulley
Bmr Strut Bar Brace
Bmr Rear Lower Control Arms
Bmr Panhard Bar
Powerstop Drilled/Slotted Rotors
Dyno Tuned By Bryan Herter (PCMforless.com)
and Holy Water in the radiator.
#18
11 Second Club
iTrader: (2)
Join Date: Oct 2008
Location: maryland
Posts: 269
Likes: 0
Received 0 Likes
on
0 Posts
My set up..
Ported/Painted LT1 Intake
58mm BBK Throttle Body
Jet Hot Longtube Headers
Catless Y-Pipe
Corsa 3" Catback Exhaust w/cut-out
3.73 Gears
17" ZR1 Rear Rims w/ 275/40/17 nitto Drag Radials
Summit Electric Waterpump
OTVC MSD Wires w/NGK TR55 Plugs
MSD Opti Cap/Rotor
MSD Coil
GM AC Delete Pulley
Bmr Strut Bar Brace
Bmr Rear Lower Control Arms
Bmr Panhard Bar
Powerstop Drilled/Slotted Rotors
Dyno Tuned By Bryan Herter (PCMforless.com)
and Holy Water in the radiator.
Ported/Painted LT1 Intake
58mm BBK Throttle Body
Jet Hot Longtube Headers
Catless Y-Pipe
Corsa 3" Catback Exhaust w/cut-out
3.73 Gears
17" ZR1 Rear Rims w/ 275/40/17 nitto Drag Radials
Summit Electric Waterpump
OTVC MSD Wires w/NGK TR55 Plugs
MSD Opti Cap/Rotor
MSD Coil
GM AC Delete Pulley
Bmr Strut Bar Brace
Bmr Rear Lower Control Arms
Bmr Panhard Bar
Powerstop Drilled/Slotted Rotors
Dyno Tuned By Bryan Herter (PCMforless.com)
and Holy Water in the radiator.