parting out car

09-30-2012, 03:52 PM

#1

jasonisdn

TECH Regular

Thread Starter

iTrader: (1)

Join Date: Jan 2007

Posts: 484

Likes: 0

Received 0 Likes on 0 Posts

parting out car

Category: Racing Parts
Price: $1600000000
Part Fits: 93-02 Chevrolet Camaro
Location (State): NC
Item Condition: Used
Engine: LT1/LT4
LS Engine?: Non-LS Part

parting out car and parts. lost interest and would rather be 30 miles offshore fishing instead of at the drag strip.
nx nitrous kit 2 stage shark nozzles 300 total shot. 20lb bottle NX 900.00

tubular k-member spohn for power steering200 without arms with arms upper and lower 600 K-member SOLD
with tubular arms upper and lower.SORRY GUYS NOT BMR SPOHN

panhard rod adjustable 75

TH400 with coan th400 manual valve body
race clutch bands
H.D. INTERMEDIATE SPRAG-34 ELEMENT 900

12 bolt strange rearend 4:10 gear set from them. upgraded race axles and bearings 1000 SOLD

385 CI 4 bolt splayed main cap LT1. motor is fresh built and has not been cranked yet (still at machine shop) mls head gaskets complete 5900.

callies dragon slayer crank 3.750 600 , compstar 6inch rods 450, je nitrous pistons .040 550

ADDEDdiamond nitrous pistons .030 for 6 inch rod 300

Spohn tubular TA (BMR BRAND WAS MY MISTAKE)
200

cheetah shifter th400 turbo shifter 150

new DR 325/50r15's never ran . mickey thompson et street 200 each or 400 both.

AI trickflow 210cc heads and custom cam 245/249 .610lift cam and heads 3000

GM lifters new and 1.6 NSA comp rockers. lifters 50 rockers 200 rockers sold

electric water pump meziere only a few hours on it (maybe 15hrs if that)

FJO progressive nitrous controller. can control both stages 150

telstar rims. i know 3.5 width on a 15, with the correct spacer for fbody cars. the rears are 10.5 or close (if someone is interested i can go look at the shop and take some pics)

stand alone fuel system (low pressure) with pump and reg and fuel cell. it's not a custom cell for the f-bodies, i made space for it.

low impedance injector driver and 60lb injectors

ASM mono blade throttle body 300

hooker long tubes recoated with the gray high temp coating. 200

LTCC coil over plug setup 200/ sold

canton road race pan 242t i think was the part number 200

trans cooler

ADDED rear lower control arms, Spohn non adjustable SOLD

ADDED factory larger than stock SS front sway bar 50

ADDED factory SS rims with new nitto drag radials on rear 300 and RR compound on the fronts 300

ADDED 4 inch cowl hood 100

ADDED 1996 Z28SS number 1053. It has never been wrecked. The nose piece is aftermarket. The paint is in good shape. The parts are coming off of it. the interior is out of the car and has been sold over a year ago. Its a t-top car. The vin is clean and clear. i will throw in the spider webs under the car for free.

these parts will not be sold at dirt cheap prices. so any body saying "ill give 500 for the nitrous kit and controller" that's worth over 1,000, need not post.
these are not cheap or trash parts. the last builder of the motor had to much clearance in the wall with the .030 bore and i had to rebuild with a .040 bore. if you want the machine shop number i'll give it to you. they are known locally for building motors that stay together under boost and nitrous. (ex. a friends mustang running 5.70's (1/8th mile) on a 76mm turbo on a true 10.5 tire with a dart small block in the low 300 CI and is very streetable. as in he can drive it 2 hours away and drive it back without issue.) there was just way to much blowby. the tranny has not been used since rebuild. some items can be shipped but buyer pays shipping

Last edited by jasonisdn; 10-08-2012 at 10:18 AM. Reason: wrong brand

parting out car

Trending Topics