LS7 Clutch/ LS2 Flywheel.
03-04-2008, 04:49 PM
#1
Banned
Thread Starter
iTrader: (14)
Join Date: Apr 2005
Location: Keller
Posts: 1,701
Likes: 0
Received 0 Likes
on
0 Posts
LS7 Clutch/ LS2 Flywheel. LS7 clutch and ls2 flywheel combo used for only 6 months. and 15k miles. grabs and works fine. I need something to support more power.
LS2 Flywheel will be resurfaced (Brand New)
Brand New its 420 for the combo. Yours for
250 Shipped!
LS2 Flywheel will be resurfaced (Brand New)
Brand New its 420 for the combo. Yours for
250 Shipped!
03-04-2008, 06:04 PM
#4
Banned
Thread Starter
iTrader: (14)
Join Date: Apr 2005
Location: Keller
Posts: 1,701
Likes: 0
Received 0 Likes
on
0 Posts
sorry my pm's are restricted cus i just got off banned. please email me at Vipersam2001@yahoo.com
thanks
thanks
Trending Topics
03-05-2008, 01:33 AM
#9
Banned
Thread Starter
iTrader: (14)
Join Date: Apr 2005
Location: Keller
Posts: 1,701
Likes: 0
Received 0 Likes
on
0 Posts
yes the rest of the hydrualics work from an ls1 setup.
email replied.
i can also get u a brand new slaves for 40 bucks.
and no i have alot of suspension parts already thanks.
TTT i need this gone ASAP
email replied.
i can also get u a brand new slaves for 40 bucks.
and no i have alot of suspension parts already thanks.
TTT i need this gone ASAP
03-05-2008, 10:58 AM
#13
TECH Enthusiast
iTrader: (7)
Join Date: Sep 2003
Location: Ft. Worth-ish
Posts: 600
Likes: 0
Received 0 Likes
on
0 Posts
Jason @ TDP had me pick up a slave w/the revised design (01-02 came with them) when he did my LS7 install.
He said he also shimmed it so it wouldn't engage right off the floor board.
If you have any questions I'm sure he'd answer them better than I can.
He said he also shimmed it so it wouldn't engage right off the floor board.
If you have any questions I'm sure he'd answer them better than I can.
03-05-2008, 11:32 AM
#14
12 Second Club
iTrader: (49)
Join Date: May 2006
Location: College Station, Texas
Posts: 966
Likes: 0
Received 0 Likes
on
0 Posts
Oh I got ya. I bet he had you pick that up simply because of the new design. As far as the physical concept goes though you can technically use the older slave.
03-05-2008, 02:46 PM
#19
12 Second Club
iTrader: (49)
Join Date: May 2006
Location: College Station, Texas
Posts: 966
Likes: 0
Received 0 Likes
on
0 Posts
Shim is totally a preference guys and I'm telling you that you can run this with the old slave. The only changes in design were internal and they look identical on the outside. I didn't shim my ls7 clutch and engagement suits me just fine. I've seen both ways though so I would just give it a shot without a shim and if you absolutely hate then go back and toss the shim there.
03-05-2008, 03:15 PM
#20
TECH Enthusiast
Join Date: Dec 2003
Posts: 529
Likes: 0
Received 0 Likes
on
0 Posts
Wait a second. An LS7 setup only runs 420 new with the flywheel? I was under the impression that they were more... like close to 1000K.
LS7 setup is pretty good for bolt ons, isn't it?
LS7 setup is pretty good for bolt ons, isn't it?