LS Swap Ready 1995 Camaro z28
#1
Launching!
Thread Starter
iTrader: (16)
Join Date: May 2010
Location: Dayton
Posts: 287
Likes: 0
Received 0 Likes
on
0 Posts
LS Swap Ready 1995 Camaro z28
This roller is LS swap ready with lots of good aftermarket parts.
1995 z28 previously ran with a 6.0l LS2 and t56 transmission. Engine and transmission were pulled to refresh, but I am now occupied with another car and dont have time for this one. ALL YOU NEED TO DO is drop in an LS and t56 and you're good to go. All aftermarket parts have less than 5000 miles on them.
Parts on the roller:
Corbeau fx1 drivers seat
UMI tubular road race k member for 98-02 (also 98-02 steering rack and shaft of course)
4 piston Brembo front brake calipers with 2 piece, 13" rotors, this brake package sells for over $2400 new.
Hawk pads front and rear
ARP wheel studs all the way around
Eibach front hub centric wheel spacers
Steel braided brake lines
Strano coil springs
KYB adjustable struts and shocks
UMI Adjustable pan hard bar
UMI Rear lower control arm relocation brackets
4.10 gears in the 10 bolt, 10 bolt was completely refreshed with new bearings, races, seals, ring and pinion, housing sand blasted and painted black.
All the bushings, ball joints, and tie rods in the front suspension have been replaced with new Moog parts.
LS fbody engine wiring harness ready to plug and play with tuned PCM
255lph walbro fuel pump
Comes with 17" corvette wheels
Car is clean underneath
I have many parts that can go with the car, with negotiations
Asp underdrive pulley
Various exhaust parts
All f body accessories, alternator, bracket, power steering
Bottom pics are of car when it was complete, looks the same now, just different wheels. Rears are plastidipped.
Asking $2500obo
Motivated to sell
1995 z28 previously ran with a 6.0l LS2 and t56 transmission. Engine and transmission were pulled to refresh, but I am now occupied with another car and dont have time for this one. ALL YOU NEED TO DO is drop in an LS and t56 and you're good to go. All aftermarket parts have less than 5000 miles on them.
Parts on the roller:
Corbeau fx1 drivers seat
UMI tubular road race k member for 98-02 (also 98-02 steering rack and shaft of course)
4 piston Brembo front brake calipers with 2 piece, 13" rotors, this brake package sells for over $2400 new.
Hawk pads front and rear
ARP wheel studs all the way around
Eibach front hub centric wheel spacers
Steel braided brake lines
Strano coil springs
KYB adjustable struts and shocks
UMI Adjustable pan hard bar
UMI Rear lower control arm relocation brackets
4.10 gears in the 10 bolt, 10 bolt was completely refreshed with new bearings, races, seals, ring and pinion, housing sand blasted and painted black.
All the bushings, ball joints, and tie rods in the front suspension have been replaced with new Moog parts.
LS fbody engine wiring harness ready to plug and play with tuned PCM
255lph walbro fuel pump
Comes with 17" corvette wheels
Car is clean underneath
I have many parts that can go with the car, with negotiations
Asp underdrive pulley
Various exhaust parts
All f body accessories, alternator, bracket, power steering
Bottom pics are of car when it was complete, looks the same now, just different wheels. Rears are plastidipped.
Asking $2500obo
Motivated to sell
Last edited by Snkebait95; 07-23-2015 at 09:51 AM.