ITB's for LS engines
#64
12 Second Club
iTrader: (28)
No updates?? In the time since this thread was started, I found/MADE time to handle the following:
...and I still haven't seen pics of this ITB setup, or a sketch... or anything...
- Go to SEMA
- My flexplate blew up on the drive out to SEMA, 30 minutes away from Vegas
- Had the car towed to my parents place 100 miles away from my apartment, ended up not going to SEMA
- Only worked on it every other weekend, due to the 100 mile one-way distance, with a DD getting 16MPG highway
- Purchased/built all of the remaining tools necessary to do an engine/trans pull/replace w/o a lift
- Pulled the motor/transmission
- Disassembled the motor down to the bare block
- Brought the bare block 100 miles back with me to the apartment
- Purchased all of the forged components necessary to rebuild the block
- Had the pistons coated by a local reputable aerospace coatings company
- Brought the block to a machine shop for initial cleanup/honing
- Paid a more reputable shop to properly assemble the shortblock
- Two months later it was complete (delays with the shop and my ordering/coating parts).
- Got a base tune put on the PCM
- Brought the shortblock 100 miles back to rejoin the car
- Turned the shortblock into a longblock
- Installed the longblock and transmission into the car
- Bled the brakes, changed all the fluids, and got the car running
- Retuned the car with a wideband and a couple of days of street tuning
- Had the transmission fail
- Found a built transmission 80 miles away
- Drove 160 miles round trip to pick up the built transmission
- Drove 50 miles to pick up the stock torque converter
- Installed the built transmission
- Now fixing other various quirks due to the car being down for 6 months and undergoing a new forged/built setup
- imagine JUST the fuel cost of all of that, considering my DD was a 4.0L Jeep that got probably 16MPG highway.
- now realize that a Harrop costs the same amount of money as what I spent on the forged motor/built trans project
...and I still haven't seen pics of this ITB setup, or a sketch... or anything...
Last edited by ZexGX; 07-15-2011 at 05:06 PM.
#65
TECH Fanatic
iTrader: (10)
No updates?? In the time since this thread was started, I found/MADE time to handle the following:
...and I still haven't seen pics of this ITB setup, or a sketch... or anything...
- Go to SEMA
- My flexplate blew up on the drive out to SEMA, 30 minutes away from Vegas
- Had the car towed to my parents place 100 miles away from my apartment, ended up not going to SEMA
- Only worked on it every other weekend, due to the 100 mile one-way distance, with a DD getting 16MPG highway
- Purchased/built all of the remaining tools necessary to do an engine/trans pull/replace w/o a lift
- Pulled the motor/transmission
- Disassembled the motor down to the bare block
- Brought the bare block 100 miles back with me to the apartment
- Purchased all of the forged components necessary to rebuild the block
- Had the pistons coated by a local reputable aerospace coatings company
- Brought the block to a machine shop for initial cleanup/honing
- Paid a more reputable shop to properly assemble the shortblock
- Two months later it was complete (delays with the shop and my ordering/coating parts).
- Got a base tune put on the PCM
- Brought the shortblock 100 miles back to rejoin the car
- Turned the shortblock into a longblock
- Installed the longblock and transmission into the car
- Bled the brakes, changed all the fluids, and got the car running
- Retuned the car with a wideband and a couple of days of street tuning
- Had the transmission fail
- Found a built transmission 80 miles away
- Drove 160 miles round trip to pick up the built transmission
- Drove 50 miles to pick up the stock torque converter
- Installed the built transmission
- Now fixing other various quirks due to the car being down for 6 months and undergoing a new forged/built setup
- imagine JUST the fuel cost of all of that, considering my DD was a 4.0L Jeep that got probably 16MPG highway.
- now realize that a Harrop costs the same amount of money as what I spent on the forged motor/built trans project
...and I still haven't seen pics of this ITB setup, or a sketch... or anything...
#66
12 Second Club
iTrader: (28)
At one point I was pretty much dying from a combination of bronchitis, the flu, and asthma. On a sick day (a week before I had to go to the ER), barely being able to stand, I brought the motor from my apartment to the motor builder and unloaded it at the motor builders shop. I place a lot of priority on car stuff, I guess. But this thread is just a tease. However, I had a lot of motivation: my Jeep was a money/gas-guzzling POS. Whereas I am unsure of how much motivation the OP has.
Edit: he hasn't logged into LS1tech since February...
Edit: he hasn't logged into LS1tech since February...
Last edited by ZexGX; 07-15-2011 at 05:49 PM.
#68
Yep...crazy. Its unfortunately a necessary evil in optimizing a build. For my build, FAST would work but would choke the cubes....Marcella's intake was on deck but couldn't build a big enough Tbody that would work on the street - idle and WOT only . Enter Kinsler.....twice what the Marcella intake was but should (better!) resolve the issues in street manners and feeding the beast. Dyno #'s in a couple weeks
#69
Banned
iTrader: (10)
Not familiar with Kinsler. My experience is limited to Harrop and Jenvey. Harrop is the only option for DBW right now. Harrop has a common plenum, and provisions for an IAC and MAP sensor common to all ports.
Jenvey is 8 seperate throttle bodies and ports. No common plenum. Jenvey, with no common plenum, has no IAC (remember this is cable, not DBW) and also, no real provision for a MAP sensor. So, it's MAP in one port, or Alpha N.
Just sayin........
Jenvey is 8 seperate throttle bodies and ports. No common plenum. Jenvey, with no common plenum, has no IAC (remember this is cable, not DBW) and also, no real provision for a MAP sensor. So, it's MAP in one port, or Alpha N.
Just sayin........