Projector light Reject Mod:: How To!!
Projector light Reject Mod:: How To!! Well the only thing that i didn't like about the new projector lights were those little led's on the side of the housing that killed the flow to the whole thing, so what i did was got them to turn off now. anyways it's super simple and you dont even have to open the headlights!!
You will first need to find a tiny sharp metel, i used the end of a spring i had laying around
Second you need to find which wires you are needing to reject.
The two wires that light up the LED's on the side of the headlight are these two
Right here is where you could clip off those two wires and be done with it making sure to just tape up the ends so that they dont short out.....or you could continue to take out the wires from the harness to be able to use them later down the road not needing to hake the wires up
If you wanted to try and keep the wires from having to cut them then continue on
you will need to disconnect the harness from one another, to do so you need to push down on the little tab that i'm pointing to with the tooth pick
note which two holes of the harness the wires i'm taking off, the two CLOSEST to the tab
what you will need to do is use your metel pick to push down on the little tab's holding the wire in place (the tab is located where you see it indexed in the center bottom of each hole)
push the tab in and pull the wire out.
These are the tab's i'm talking about
once they are both out tape them seperatly (as to not short out with one another) then tape then together around the main harness (to not get in the way when you install the headlight
plug it all back up.....
throw the headlights on the car..... wire them up how ever you wire them up....
.....
...
BAM!!
Rejected LED's mod
simple enough huh!!
i just wanted to do a write up and have a mod actually named after me! what better mod to use than rejecting the side led's!!
anyways hope you enjoy
You will first need to find a tiny sharp metel, i used the end of a spring i had laying around
Second you need to find which wires you are needing to reject.
The two wires that light up the LED's on the side of the headlight are these two
Right here is where you could clip off those two wires and be done with it making sure to just tape up the ends so that they dont short out.....or you could continue to take out the wires from the harness to be able to use them later down the road not needing to hake the wires up
If you wanted to try and keep the wires from having to cut them then continue on
you will need to disconnect the harness from one another, to do so you need to push down on the little tab that i'm pointing to with the tooth pick
note which two holes of the harness the wires i'm taking off, the two CLOSEST to the tab
what you will need to do is use your metel pick to push down on the little tab's holding the wire in place (the tab is located where you see it indexed in the center bottom of each hole)
push the tab in and pull the wire out.
These are the tab's i'm talking about
once they are both out tape them seperatly (as to not short out with one another) then tape then together around the main harness (to not get in the way when you install the headlight
plug it all back up.....
throw the headlights on the car..... wire them up how ever you wire them up....
.....
...
BAM!!
Rejected LED's mod
simple enough huh!!
i just wanted to do a write up and have a mod actually named after me! what better mod to use than rejecting the side led's!!
anyways hope you enjoy
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
. 
slight problem guys 
i'm going to have to swap the headlights out to the stockers for a week and send these back, my cut off pattern on the passenger side was total crap, the shield inside the headlight was not curved right and instead of wanting to fix it myself i'm going to send them back to get a new set, so the blinker integration mod will have to hold off on my end for now. but for other's out there than cant wait and are average with wiring, it's very simple...
one thing i forgot to add to the picture below is to not cut the ground wire (black) on the picture it is tooken off but you must leave it connected or else your LED's wont work!!!
i'm going to have to swap the headlights out to the stockers for a week and send these back, my cut off pattern on the passenger side was total crap, the shield inside the headlight was not curved right and instead of wanting to fix it myself i'm going to send them back to get a new set, so the blinker integration mod will have to hold off on my end for now. but for other's out there than cant wait and are average with wiring, it's very simple...one thing i forgot to add to the picture below is to not cut the ground wire (black) on the picture it is tooken off but you must leave it connected or else your LED's wont work!!!
Nice write up. I was going to do the same thing but I was to lazy to do it. I just wanted my projectors in. I will have to think about doing this now so I don't have the LED's on with the halo's.
Mike
Mike
yeah, the LED's just kill it when they are on all the time, if you do the blinker deal post it up here and a different wiring diagram if you used a diff one, i hope i can get my newer one's in fast to post a vid of the blinker mod
