**Specialized Stainless Camaro Build**
Thread Starter
FormerVendor
iTrader: (15)
Joined: Jun 2006
Posts: 2,689
Likes: 0
From: Los Angeles, CA
I ended up using:
2 rolls of BXT
6 yards of Ensolite
2 cans of glue
Thread Starter
FormerVendor
iTrader: (15)
Joined: Jun 2006
Posts: 2,689
Likes: 0
From: Los Angeles, CA
Thread Starter
FormerVendor
iTrader: (15)
Joined: Jun 2006
Posts: 2,689
Likes: 0
From: Los Angeles, CA
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Looking good Steve!
Just curious as to why you didn't put this in the Sponsor Projects section?
I thought that was exactly why that forum was created for you guys. I will ask if this can be moved...
Just curious as to why you didn't put this in the Sponsor Projects section?
I thought that was exactly why that forum was created for you guys. I will ask if this can be moved...
Thread Starter
FormerVendor
iTrader: (15)
Joined: Jun 2006
Posts: 2,689
Likes: 0
From: Los Angeles, CA
Because the members here can't respond or interact with the thread if it's in the project section. I'm planning on moving it there after I finish the build.
Thread Starter
FormerVendor
iTrader: (15)
Joined: Jun 2006
Posts: 2,689
Likes: 0
From: Los Angeles, CA
I was going to polish the face of my stock rims but got lazy and just purchased some 35th Anniversary machined face 10 spokes 
Should be here in a week or so...
Here's the white face gauges and shift **** installed. I cut the shaft on the shifter 3/4". I'm happy with the way everything turned out!
Gauges before:
After:
Should be here in a week or so...Here's the white face gauges and shift **** installed. I cut the shaft on the shifter 3/4". I'm happy with the way everything turned out!
Gauges before:
After:
^^Macewenmotorsports.com Damn now I want a shifter one....ahhh money
Everything looks great
How long did it take for you to get your decals?
Everything looks great
How long did it take for you to get your decals?
Last edited by Ls1CamaroGuy87; Mar 4, 2008 at 05:43 PM.
^^cut around the metal tube (black) first at whatever mearurement you want (1 inch at the most!), and then measure the exact same length on the white peice once the black peice has been cut and cut it...
Thread Starter
FormerVendor
iTrader: (15)
Joined: Jun 2006
Posts: 2,689
Likes: 0
From: Los Angeles, CA
I cut where the keyways are for the clip that holds your stock **** on. I cut the same amount off the plastic shaft. Then I extended the groove on the metal shaft 3/4" with a small carbide endmill. You have to be careful not to damage the plastic shaft!