Wtf now im pissied!
#23
nice more options... anything going to be done about the transmission of vibrations through the solid mounts???
solid mount are great and all but vibs are the whole reason my RC51 MM are sitting on the shelf
haha i stand corrected.. only problem with the aftermarket mounts are that they dont include a positive lock like the OEM designs..its all poly and when that fails you got nothing.. with tha being said im running MM that dont have a positive lock so ill just STFU now hahah
solid mount are great and all but vibs are the whole reason my RC51 MM are sitting on the shelf
haha i stand corrected.. only problem with the aftermarket mounts are that they dont include a positive lock like the OEM designs..its all poly and when that fails you got nothing.. with tha being said im running MM that dont have a positive lock so ill just STFU now hahah
#24
TECH Resident
iTrader: (1)
Join Date: Sep 2010
Location: Winnipeg, mb
Posts: 789
Likes: 0
Received 0 Likes
on
0 Posts
haha i stand corrected.. only problem with the aftermarket mounts are that they dont include a positive lock like the OEM designs..its all poly and when that fails you got nothing.. with tha being said im running MM that dont have a positive lock so ill just STFU now hahah
With the oem failed tranny mount when I went over speed bumps I could feel my shifter rise in my hand, then the the tranny would clunk back down.
I have UUC now, but plan on switching it out to a Creative steel grey mount.
#26
Sorry if this sounds dumb, But what does it feel like when the mount comes apart such as yours? Is the motor bouncing around and clunking? Just want the heads up to pay attention to mine as I bought and installed mine a few months ago.
#28
TECH Addict
iTrader: (14)
Join Date: Feb 2007
Location: Owasso, OK
Posts: 2,342
Likes: 0
Received 0 Likes
on
0 Posts
nice more options... anything going to be done about the transmission of vibrations through the solid mounts???
solid mount are great and all but vibs are the whole reason my RC51 MM are sitting on the shelf
haha i stand corrected.. only problem with the aftermarket mounts are that they dont include a positive lock like the OEM designs..its all poly and when that fails you got nothing.. with tha being said im running MM that dont have a positive lock so ill just STFU now hahah
solid mount are great and all but vibs are the whole reason my RC51 MM are sitting on the shelf
haha i stand corrected.. only problem with the aftermarket mounts are that they dont include a positive lock like the OEM designs..its all poly and when that fails you got nothing.. with tha being said im running MM that dont have a positive lock so ill just STFU now hahah
Also, the CS trans mount supposedly has a fail safe similar to the OEM mount in case of failure. Personally, I had the UUC trans mount and I threw it in the trash and learned a long time ago UUC is a joke. I run the RC51 mounts with the stock trans mount and even with a loppy cam it's really not bad! I know they are much better than failed OEM mounts lol
#29
On The Tree
Thread Starter
Join Date: Sep 2010
Location: Chicago,IL
Posts: 120
Likes: 0
Received 0 Likes
on
0 Posts
this time i felt and heard a clunking when i decided to look under the car. im getting pretty good at changing motor mounts (and removing longtubes) lol. also spoke with UUC today, and they told me the design was changed and i will be recieving the new one.
#32
TECH Enthusiast
iTrader: (4)
Join Date: Jun 2009
Location: Portland, OR
Posts: 574
Likes: 0
Received 0 Likes
on
0 Posts
If someone can get me some dimensions on the RC51 mounts, P/N's for the bushing used, or if someone has some on the shelf, I have a buddy that can fab some up, and get a price to see if he's willing to make another run of them.
I can coordinate this effort as well.
I can coordinate this effort as well.
#35
TECH Enthusiast
iTrader: (2)
Join Date: Jan 2009
Location: Texas
Posts: 626
Likes: 0
Received 0 Likes
on
0 Posts
Trust me. Replace the tranny mount while your at it. Takes twenty minutes. If the tranny mount is worn/damaged/separated, it will allow the motor to deflect even more. You have give somewhere allowing your motor to deflect and separate your drivers side mount.
Bad workmanship- possibility YES!
But do you want to replace MM and tranny again wh you find out it's not a workmanship issue?
It's up to you. The Internet is full of tons of good info, and twice as much bad. You have to think logically on your own, because it's your car and your money. Just look at the big picture. Two failed UUC!?
Tranny and vibes - I have CS mm and tranny, no excess vibes here. Anyone else?
Bad workmanship- possibility YES!
But do you want to replace MM and tranny again wh you find out it's not a workmanship issue?
It's up to you. The Internet is full of tons of good info, and twice as much bad. You have to think logically on your own, because it's your car and your money. Just look at the big picture. Two failed UUC!?
Tranny and vibes - I have CS mm and tranny, no excess vibes here. Anyone else?
#36
TECH Fanatic
iTrader: (8)
Join Date: Jun 2010
Location: Helendale
Posts: 1,921
Likes: 0
Received 0 Likes
on
0 Posts
this whole mount issue is weird...some have failures and some dont. be it the stockers, UUC, or CS. some have melted and some are doing fine.
my stockers were shot after 33k on the clock. so, rather then getting stockers replace under warranty (since a lot of had issue doing that with a modded car), i replaced them with UUC at the recommendation of my shop. i now have almost 10k miles on them, with no issues. i am running Kooks LTs with Jet Hot 1700 Coating and the MM have header wrap and heat sheilds with them.
OP, sorry to here about the bad luck. hope you get her back up soon with no other problems
my stockers were shot after 33k on the clock. so, rather then getting stockers replace under warranty (since a lot of had issue doing that with a modded car), i replaced them with UUC at the recommendation of my shop. i now have almost 10k miles on them, with no issues. i am running Kooks LTs with Jet Hot 1700 Coating and the MM have header wrap and heat sheilds with them.
OP, sorry to here about the bad luck. hope you get her back up soon with no other problems
#37
On The Tree
Join Date: Jul 2008
Location: Corn Belt, IN.
Posts: 178
Likes: 0
Received 0 Likes
on
0 Posts
I made my own. The factory mount was trashed. Too weak of a design in my opinion.
At the same time I filled the factory trans mount. I will say that the filled oem trans mount transfers more internal transmission gear noise to the cabin. It could totally be contributed to the fact that is 94 hardness rubber.
At the same time I filled the factory trans mount. I will say that the filled oem trans mount transfers more internal transmission gear noise to the cabin. It could totally be contributed to the fact that is 94 hardness rubber.
Last edited by CORNER CARVER; 03-18-2011 at 09:20 AM.
#38
TECH Resident
iTrader: (1)
this whole mount issue is weird...some have failures and some dont. be it the stockers, UUC, or CS. some have melted and some are doing fine.
my stockers were shot after 33k on the clock. so, rather then getting stockers replace under warranty (since a lot of had issue doing that with a modded car), i replaced them with UUC at the recommendation of my shop. i now have almost 10k miles on them, with no issues. i am running Kooks LTs with Jet Hot 1700 Coating and the MM have header wrap and heat sheilds with them.
OP, sorry to here about the bad luck. hope you get her back up soon with no other problems
my stockers were shot after 33k on the clock. so, rather then getting stockers replace under warranty (since a lot of had issue doing that with a modded car), i replaced them with UUC at the recommendation of my shop. i now have almost 10k miles on them, with no issues. i am running Kooks LTs with Jet Hot 1700 Coating and the MM have header wrap and heat sheilds with them.
OP, sorry to here about the bad luck. hope you get her back up soon with no other problems
#39
Structurally, the RC51, UMI, and the PFADT designs are pretty much the same. The PFADT are really nice looking.
"RC51"
PFADT, $250
Looking at the UUC abortion of a design, it's just a matter of time until they fail. I'd hate to be the guy hitting the throttle hard after apexing a turn then to have the motor rip the mount. Or, Id hate to be the guy driving behind him/her. Just say'n.
"RC51"
PFADT, $250
Looking at the UUC abortion of a design, it's just a matter of time until they fail. I'd hate to be the guy hitting the throttle hard after apexing a turn then to have the motor rip the mount. Or, Id hate to be the guy driving behind him/her. Just say'n.
Last edited by Slithering_Joe; 03-20-2011 at 12:01 PM.