The OFFICIAL X-Body Swap Thread
#101
Teching In
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
https://ls1tech.com/forums/conversio...l90e-swap.html
Mounts: BRP
Oil Pan: LH8
Headers: BRP
Accessories: Stock Truck I hope with vintage air compressor up top.
Mounts: BRP
Oil Pan: LH8
Headers: BRP
Accessories: Stock Truck I hope with vintage air compressor up top.
#104
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I used them on my 66 GTO project, completely different vehicle than yours, nothing really fit very well, and the LH8 pan hangs down too low for my comfort, some people like BRP, some like Holley it’s your choice, I just recommend doing your research and read up on others experiences and make your decision.
#106
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Hi guys,
Whilst not new to doing crazy engine swapa, I am new to the LS world and Loving IT!!!
I need help.....
A friend has fitted a 97 'vette c5 engine with a Turbo 400 to a 4 door saloon as a sleeper BUT the ECM (LS1A) is toast!
He's bought a 411 ECM to replace it which brings me to my questions:
As this engine is Drive By Wire which TAC module and Pedal assy do we need to run
And
All the wiring conversion charts that I can find do not list the TAC connections... Can anybody point me in the direction of a COMPLETE pinout for the LS1A ECM and for the 411
(On the LS1a ECM we have wires on Red C1-64 and Blue C2-71,72,77 that I can't identify...)
Thanks
Bob
Whilst not new to doing crazy engine swapa, I am new to the LS world and Loving IT!!!
I need help.....
A friend has fitted a 97 'vette c5 engine with a Turbo 400 to a 4 door saloon as a sleeper BUT the ECM (LS1A) is toast!
He's bought a 411 ECM to replace it which brings me to my questions:
As this engine is Drive By Wire which TAC module and Pedal assy do we need to run
And
All the wiring conversion charts that I can find do not list the TAC connections... Can anybody point me in the direction of a COMPLETE pinout for the LS1A ECM and for the 411
(On the LS1a ECM we have wires on Red C1-64 and Blue C2-71,72,77 that I can't identify...)
Thanks
Bob
#108
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I just installed the Holley/hooker "kit" if you will, into 74 Ventura. Mounts crossmember all fit great, headers (mid-length 2.5") fit great around the steering box. The only issue I've had is with center link interference to the pan (302-2), if you're doing a nova you should be good.
#109
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Somewhat bringing this thread back from the dead, but here is my swap in a 4th gen: 78 Nova LS Swap
Engine: 2002 LQ4 with LS2 rods & pistons (iron block LS2!)
Transmission: 2004 4L80e (4BSP from an Express Van)
Headers: Speed Engineering 1 3/4" long tubes
Engine Mounts: TSP 81100
Transmission Crossmember: Stock / Modified Stock
Oil Pan: TSP 81074
Accessories: Stock Truck Alt & PS, planning on a low mount AC w/SD7 compressor and ICT Billet Low Mount kit
Intake Manifold: 2008 TBSS (12580420) fits under stock hood!
Engine: 2002 LQ4 with LS2 rods & pistons (iron block LS2!)
Transmission: 2004 4L80e (4BSP from an Express Van)
Headers: Speed Engineering 1 3/4" long tubes
Engine Mounts: TSP 81100
Transmission Crossmember: Stock / Modified Stock
Oil Pan: TSP 81074
Accessories: Stock Truck Alt & PS, planning on a low mount AC w/SD7 compressor and ICT Billet Low Mount kit
Intake Manifold: 2008 TBSS (12580420) fits under stock hood!