Stans 1968 camaro LS swap and other upgrades!
02-12-2012, 09:52 PM
#561
Cap it if you dont have power booster for brakes, as it is a vacuum port.
02-28-2012, 09:35 PM
#563
TECH Fanatic
Thread Starter
Join Date: Nov 2010
Posts: 1,679
Likes: 0
Received 0 Likes
on
0 Posts
Well little update guys,brakes are one,lines are ran!just need to put master cylinder booster in and hook lines up !then fill up and bleed!!been slow going !!also got my Holley dominator EFI and all harness except for the 4l60 harness!!started pulling stock computer out and the stock wiring harness!!!
02-29-2012, 04:13 AM
#565
Registered User
Join Date: Feb 2012
Location: miami,FL
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
Waz up ppl. Hi im tony. Im new to the ls motor game, i have been around oil and tools for many yrs. But im going into some new things for the 2012. Ok so here i go. I just got a gm-6.0l lq9 off an 2006 escalade awd. Its complete from water pump to tranny back tail. But i dont have the wireharness. Im putting it on a 1988 monte carlo ls t-top. Can some one tell me how to start!??? P.s i want it to run like if it still was on the truck (stock) but will upgrade as time comes...
02-29-2012, 05:43 PM
#569
Waz up ppl. Hi im tony. Im new to the ls motor game, i have been around oil and tools for many yrs. But im going into some new things for the 2012. Ok so here i go. I just got a gm-6.0l lq9 off an 2006 escalade awd. Its complete from water pump to tranny back tail. But i dont have the wireharness. Im putting it on a 1988 monte carlo ls t-top. Can some one tell me how to start!??? P.s i want it to run like if it still was on the truck (stock) but will upgrade as time comes...
03-01-2012, 12:00 PM
#571
TECH Fanatic
Thread Starter
Join Date: Nov 2010
Posts: 1,679
Likes: 0
Received 0 Likes
on
0 Posts
Tsnow678,I bought Z06psi kenne bell Off of his corvette,should be here next week or two!!so yet another project to get the car running!!here is z06psi build thread so you can see the blower!!!
https://ls1tech.com/forums/forced-induction/860935-kenne-bell-install-numbers-now-well.html
https://ls1tech.com/forums/forced-induction/860935-kenne-bell-install-numbers-now-well.html
03-14-2012, 11:17 AM
#577
TECH Fanatic
Thread Starter
Join Date: Nov 2010
Posts: 1,679
Likes: 0
Received 0 Likes
on
0 Posts
here is the bracket i made that goes behind glove box from kickpanel area to radio area to hole new PCM..
bracket mounted!
here is the PCM mounted,i will need to make a cover,to cover the wires where they plug in at the bottom since that will be exposed.
here is where i ended up making a hole through for my harnesses!
bracket mounted!
here is the PCM mounted,i will need to make a cover,to cover the wires where they plug in at the bottom since that will be exposed.
here is where i ended up making a hole through for my harnesses!
03-14-2012, 01:07 PM
#578
Looking good Stan!!! I accidentily skipped over the part about you having a baby, sorry!!! Congrats in advance on the arrival of the baby!!! Now it all makes sense, you haven't had time to put those springs in cause you were too busy making love all the time, cant blame ya!!! I like the looks of the Holley setup. Great job on the bracket and ECM location but what about air conditioning? Again, Congratulations!!!
03-14-2012, 01:28 PM
#579
TECH Fanatic
Thread Starter
Join Date: Nov 2010
Posts: 1,679
Likes: 0
Received 0 Likes
on
0 Posts
Lol,yeah I'm in rush to get car back running before may ,that's when wife is due!looks like springs and kenne bell may have to wait till next fall!just not enough time!!!
