71 Chevelle+LY6+T56,

Reply Subscribe

Thread Tools

Search this Thread

Jan 7, 2012 | 09:23 PM

#21

lownfast

Thread Starter

TECH Enthusiast

iTrader: (4)

Joined: Dec 2005

Posts: 502

Likes: 0

Did some work, cut the trans tunnel. test fitting the motor and trans tomorrow.

Jan 8, 2012 | 06:18 PM

#22

lownfast

Thread Starter

TECH Enthusiast

iTrader: (4)

Joined: Dec 2005

Posts: 502

Likes: 0

12 bolt is all painted, new bushings installed.

destroyed a 4x4 wood block in the process.

Jan 8, 2012 | 06:25 PM

#23

lownfast

Thread Starter

TECH Enthusiast

iTrader: (4)

Joined: Dec 2005

Posts: 502

Likes: 0

i plan to modify these mounts so i can use the factory LS ac compressor. decided to test fit just to see how close i am.

oil pan clearance

Last edited by lownfast; Jan 9, 2012 at 10:29 AM.

Jan 8, 2012 | 06:33 PM

#24

lownfast

Thread Starter

TECH Enthusiast

iTrader: (4)

Joined: Dec 2005

Posts: 502

Likes: 0

Sits in the frame nicely.

Firewall clearance

Jan 8, 2012 | 06:42 PM

#25

lownfast

Thread Starter

TECH Enthusiast

iTrader: (4)

Joined: Dec 2005

Posts: 502

Likes: 0

Wonder if i need this little piece that sticks up?

Jan 8, 2012 | 06:49 PM

#26

lownfast

Thread Starter

TECH Enthusiast

iTrader: (4)

Joined: Dec 2005

Posts: 502

Likes: 0

little more trimming and we should be shittin' in high cotton.

Jan 8, 2012 | 06:52 PM

#27

lownfast

Thread Starter

TECH Enthusiast

iTrader: (4)

Joined: Dec 2005

Posts: 502

Likes: 0

All put up till next weekend...

Jan 9, 2012 | 06:40 AM

#28

71Fakes

On The Tree

iTrader: (2)

Joined: Jun 2011

Posts: 170

Likes: 0

From: Nashville, TN

lownfast - I plan to removing any unnecessary tab on the trans that gets in my way. It might be used for something, on some OE fitment...but not on my build.

Was this the first time the motor sat in the car? If so - congratulations. Big step.

Troy

LS1 Tech Stories

The Best V8 Stories One Small Block at Time

Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?

Pouria Savadkouei

Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine

Verdad Gallardo

7 Most Reliable High-Performance Engines GM Has Ever Built

Verdad Gallardo

Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin

Verdad Gallardo

6 Common C5 Corvette Failures and What's Involved In Repairing Them

Pouria Savadkouei

Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph

Verdad Gallardo

Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked

Pouria Savadkouei

Top 10 Most Powerful Chevy Trucks Ever Made!

Hennessey's New Supercharged Silverado ZR2 Has 700 HP

Verdad Gallardo

Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes

Verdad Gallardo

Jan 9, 2012 | 10:34 AM

#29

lownfast

Thread Starter

TECH Enthusiast

iTrader: (4)

Joined: Dec 2005

Posts: 502

Likes: 0

Quote:

Originally Posted by 71Fakes

Yes sir, this was the first time the engine met the car. So far they are getting along well. The engine pictured is a 6.0 with 317 heads I bought to use with a turbo. But I have changed plans and have an LY6 engine now. I'll have to find the 6.0 a new home at some point.

I think I'll just trim the ear off the Trans. It should be just fine.

Jan 15, 2012 | 09:13 PM

#30

lownfast

Thread Starter

TECH Enthusiast

iTrader: (4)

Joined: Dec 2005

Posts: 502

Likes: 0

This is pretty much the permanent fitment of the engine/trans. the engine is level side to side, and its all set at 4 degrees down. My tie rods hit my oil pan, so i added 1/4 inch shims and now i have plenty of clearance lock to lock.

Jan 15, 2012 | 09:20 PM

#31

lownfast

Thread Starter

TECH Enthusiast

iTrader: (4)

Joined: Dec 2005

Posts: 502

Likes: 0

I have plenty of clearance from the firewall to the engine and bell housing.

Driver side

passenger side

Time to start covering the trans up

Jan 15, 2012 | 09:29 PM

#32

lownfast

Thread Starter

TECH Enthusiast

iTrader: (4)

Joined: Dec 2005

Posts: 502

Likes: 0

I guess i got lucky, my trans is sitting at 4 degrees and it bolted to the factory crossmember with no modification needed, and as an added bonus the crossmember is bolted to the frame using factory mounting holes!

Jan 15, 2012 | 09:38 PM

#33

lownfast

Thread Starter

TECH Enthusiast

iTrader: (4)

Joined: Dec 2005

Posts: 502

Likes: 0

The 12 bolt is finally home hanging in the frame.

Jan 15, 2012 | 09:52 PM

#34

lownfast

Thread Starter

TECH Enthusiast

iTrader: (4)

Joined: Dec 2005

Posts: 502

Likes: 0

Had one issue, i bought BMR adjustable upper control arms, and the driver side hits the housing, im not very happy about having to cut up a brand new over priced part, i would say BMR's R&D is lacking at the least...

Jan 16, 2012 | 09:05 PM

#35

lownfast

Thread Starter

TECH Enthusiast

iTrader: (4)

Joined: Dec 2005

Posts: 502

Likes: 0

Im still undecided if i want to notch my frame to fit the factory LS compressor or use the kwik relocation,

Jan 17, 2012 | 05:34 AM

#36

Rucumn

Staging Lane

Joined: Dec 2007

Posts: 85

Likes: 0

Quote:

Originally Posted by lownfast

Im still undecided if i want to notch my frame to fit the factory LS compressor or use the kwik relocation,

I am at these decision points with my '67 chevelle now. I have spent some time looking at pictures of the Kwik set up and it is a presentable and affordable option, but I am leaning toward modifying the crossmember for a few reasons.

1. my frame had previously been repaired on the passenger front frame horn, so not concerned about ruining a perfect frame. Minor repair and still a good frame, but just makes the decision easier for me.
2. I plan to make precise cuts so that if I ever wanted to weld the piece back in to give it the stock appearance I will have the piece I cut out.
3. probably the biggest reason is to save a couple hundred $$$$ for other necessities.

You are ahead of me, so keep the updates coming!