1-87 chevy

iTrader: (15)

looks good !!! your just up the road from me . i also have an lsx mustang, but cant seem to get finished!

1bad03snake

iTrader: (16)

How far along are you? Im ordering my driveshaft today and exhaust kit. I was told my harness was going to ship the 9th so far no harness. I should have used PSI

1-87 chevy

iTrader: (15)

i actually had it ready to run ,then a friend offered to buy my 243s so i sold them. i then purchased some ai 226s, a victor jr and a plate kit . now iam going thru the motor since i have it apart.

1bad03snake

iTrader: (16)

Once i get mine running and driving im going to start on a 6.0 build

1bad03snake

iTrader: (16)

More parts showed up

blubu

iTrader: (10)

Looking good!

1bad03snake

iTrader: (16)

I got the 7.5 out and set out for the trash men. I also got the steering shaft moved over ( thanks Don). The flaming river rack and shaft are in and adjusted to be close enough to roll around. One of my rear race star rims are bent (wtf). So to make it worse they sent me 12mm lug nuts not 1/2x20. So the car still sits on jack stands. I got the t5 tranny mount drilled for the turbo 350 and tomorrow I'll slot the crossmember so it fits better. I'm going to clean up the underside of the car and get the 8.8 installed.

LS1PUNK

iTrader: (5)

Looking good.

I didnt realize you where in DP. If you would like u can come by and check out how I had mine wired.

1bad03snake

iTrader: (16)

That would be great lmk when it's convenient for you. I'm off until Friday night

tex1978

iTrader: (3)

Looking good. Im in the same boat. 4 banger coupe to LS1 alternator. Ive tried to figure out how to mount the 4banger alt on the 6.0L somehow but kinda at a stand still on mine till I get my rearend built and minitubs finished. Long way from working on the motor.

If you get if figured out post up. Ive got an LS1 alternator and the Ford one. Plug and play would be nice.

LS1PUNK

iTrader: (5)

Mine is using a LS1, I think Matt got some pics of it today.

I dont mess with wiring so he'll have to chime in on how it was done.

1bad03snake

iTrader: (16)

Are you going to run the ford solenoid? If not run a #4 from the gm alt to the starter. I took a few pics of Tim's car. The wiring is done nice and clean. I hope to try to duplicate it this week while im off

1bad03snake

iTrader: (16)

Got the rear finished up today. Tomorrow I'm going to install new shocks and start on the battery,starter,alt wiring

v8sten

iTrader: (5)

Here is my coupe with Matts wheels on it

1bad03snake

iTrader: (16)

Wiring starts tomorrow along with finishing up the rear disk brakes.

1bad03snake

iTrader: (16)

I ordered my gauges today. I went with the brushed aluminum background and ultra light gauges. I also go the cars lights to come on. So it looks like I should be starting the car by this weekend




The right lug nuts finally showed up also. I'm waiting on 02's and Lakewood rear shocks to come in. The cluster will be here in 7-10 days

ocp04

where did you find that cluster looks great. thanks joe

1bad03snake

iTrader: (16)

Florida50.com. talk to any he knows his stuff

tex1978

iTrader: (3)

Hows the alt wiring coming??

1bad03snake

iTrader: (16)

Alt is done! Now im wiring up the harness/fans/fuel pump