72 Comet with a turbo/LS 5.3 in it's future.....
#761
8 Second Club
iTrader: (4)
Might try draining out all the fluid and going with HYgard or equivalent fluid. typically tightens up the converter 200-300rpm or so... Great fluid for the price as well. Handles heat better than non synthetic ATF's.
I pick up the 5 gallon buckets at the local tractor supply stores. Or amazon carries it in gallon jugs. I'd run the standard viscosity to tighten it up the most.
I pick up the 5 gallon buckets at the local tractor supply stores. Or amazon carries it in gallon jugs. I'd run the standard viscosity to tighten it up the most.
#762
Old School Heavy
iTrader: (16)
Might try draining out all the fluid and going with HYgard or equivalent fluid. typically tightens up the converter 200-300rpm or so... Great fluid for the price as well. Handles heat better than non synthetic ATF's.
I pick up the 5 gallon buckets at the local tractor supply stores. Or amazon carries it in gallon jugs. I'd run the standard viscosity to tighten it up the most.
I pick up the 5 gallon buckets at the local tractor supply stores. Or amazon carries it in gallon jugs. I'd run the standard viscosity to tighten it up the most.
#764
I did not make it out to tnt last Wed nite, but I did go down to Bradenton on Sat for the season opener for brackets..... First thing that happened when I got down there I found out the Thortons on 64 no longer ha E85, instead they now have non ethanol(big switch)..... So I topped it off with 7 gal of 93 oct, good thing I have a Flex Fuel Veichle(ethanol sensor equipped)..... Checked the fuel when I got to the track and I was on E45, at least it was close to E50..... Surprisingly it still went 6.51 and two 6.52's, not too bad on 12lbs of boost..... I figured out the converter slippage and it's a redicalous 30%, I have to get a converter ordered.....
Then the big scare on the way home, just as I was getting on the Skyway Bridge I noticed my oil pressure drop to zero and bounce back up..... I was screwed at this point so I kept going while watching the pressure bounce between 40 and 0, I made it over the bridge with no abnormal motor noises and it wasn't heating up at all either..... So I stopped at the scenic outlook by the north tool booths and hooked the laptop up(the gauge has it's own sensor, but the ecu reads the factory sensor)..... Oil pressure looked good idling so I hit the road again and it maintained 57-59 lbs on the lap top(the gauge was all over the place)..... I'll have to get a new sensor.....
I also weighed the car on Sunday, this is one heavy bitch for what it is..... It weighs 3405 with me in it, balance is really good though(49% front and 51% rear)..... Problem is it's heavy on the right rear by 80lbs, I am going to have to do something about that.....
Then the big scare on the way home, just as I was getting on the Skyway Bridge I noticed my oil pressure drop to zero and bounce back up..... I was screwed at this point so I kept going while watching the pressure bounce between 40 and 0, I made it over the bridge with no abnormal motor noises and it wasn't heating up at all either..... So I stopped at the scenic outlook by the north tool booths and hooked the laptop up(the gauge has it's own sensor, but the ecu reads the factory sensor)..... Oil pressure looked good idling so I hit the road again and it maintained 57-59 lbs on the lap top(the gauge was all over the place)..... I'll have to get a new sensor.....
I also weighed the car on Sunday, this is one heavy bitch for what it is..... It weighs 3405 with me in it, balance is really good though(49% front and 51% rear)..... Problem is it's heavy on the right rear by 80lbs, I am going to have to do something about that.....
#765
8 Second Club
iTrader: (4)
Oh man that’s heavier than I would have thought… great times for 3400lbs and 12psi. Might temporarily toss a sand bag in the driver side rear and see if she responds well. Adding weight didn’t affect my 1/8th mile speed much at all. I put 120lbs in the rear of and lost maybe a half MPH… but the ET was much improved. If all is well you can order 35lb lead bricks they use for the kart racing on EBay. Then bolt them where needed
FWIW I actually prefer E60 or so. Seems to keep injectors clean (no e85 goo build up) and provides plenty of knock resistance. Running 14lbs or so with no intercooler on my 5.3.
FWIW I actually prefer E60 or so. Seems to keep injectors clean (no e85 goo build up) and provides plenty of knock resistance. Running 14lbs or so with no intercooler on my 5.3.
#766
Oh man that’s heavier than I would have thought… great times for 3400lbs and 12psi. Might temporarily toss a sand bag in the driver side rear and see if she responds well. Adding weight didn’t affect my 1/8th mile speed much at all. I put 120lbs in the rear of and lost maybe a half MPH… but the ET was much improved. If all is well you can order 35lb lead bricks they use for the kart racing on EBay. Then bolt them where needed
FWIW I actually prefer E60 or so. Seems to keep injectors clean (no e85 goo build up) and provides plenty of knock resistance. Running 14lbs or so with no intercooler on my 5.3.
FWIW I actually prefer E60 or so. Seems to keep injectors clean (no e85 goo build up) and provides plenty of knock resistance. Running 14lbs or so with no intercooler on my 5.3.
I think it actually liked having less ethanol in it, plus I am injecting water/meth.....
#769
I figured it was time for a little update, I didn't do much to it for a couple weeks but I was wanting to change the seat so that project has started..... I was sitting higher then I wanted in the car and technically have no usable head rest on the seat that were in it, and I really liked the 41 series Kirkey Pro Drag Seat that were in my 85 Coupe..... Since my car weighs in like a tank i should be able to kill some weight too..... So I am in the process of putting a set of the new Kirkey 55 series Pro Drag Seats in the Comet, bad part is it opened a whole can of worms I wasn't thinking about..... No I have to move the lap belt mounts because of the new seat positioning, big pita because I had to take the rear carpet all up(which was glued down)..... I am also going the rear seat delete direction so I removed all the rear seat retaining brackets and rear seat belt mounts....... Everything in the rear is already firewalled off so I will be able to just carpet the rear area..... I removed the old lap belt mounts..... The seat are currently at work to get some brackets welded on, then I will have to add new lap belt mounts at the correct angle and position.....
Here's what it looks like after today.....
Oh yeah, I also received this little trinket at the end of last week, hopefully this helps solve the slippage problem.....
Here's what it looks like after today.....
Oh yeah, I also received this little trinket at the end of last week, hopefully this helps solve the slippage problem.....
#771
I did finally get the seat fiasco finished..... I tried to take it to the track on feb 24th for a race but the fuel pump overheated..... It didn't seem to be running right when I was approaching the track, then when I got in and was driving through the pits it shut off..... Pump heated up and lost pressure, the pump body was hot..... After it cooled for a while the car would start..... I let it cool for a couple hours, hooked up the lap top so I could monitor pressure and drove it home..... I only hat to stop once after I got off the highway..... I pissed me off and I just let it sit for a couple weeks.....
Here's what the interior looks like.....
Here's what the interior looks like.....
#772
I did get some stuff apart last weekend, and ordered some parts..... Hopefully this time around will cure some problems..... I am currently sitting in Tennessee and will be getting back to it next weekend..... I am also thing of just changing it back to gas(it not the easiest thing getting the E85 around me, there's basically only one station even close)..... And I can just up the water/meth injection a little more.....
Here's some pic's of how the car sits at the moment.....
Here's some pic's of how the car sits at the moment.....
#775
Made some progress this weekend...... Sat I got everything removed from the trunk that would be in my way..... Then I cut out the material that the Mustang gas tank mounted to, so I can build a new structure to hold the new fuel cell and rearrangement of other things in the trunk.....
Progress pic's.....
Then Sunday I cleaned up all the cut off tubes where they were attached to the frame, and trimmed the opening a little..... After that I started building the new structure.....
Sunday progress.....
Progress pic's.....
Then Sunday I cleaned up all the cut off tubes where they were attached to the frame, and trimmed the opening a little..... After that I started building the new structure.....
Sunday progress.....
#780
I definitely know the feeling... For me, it's helped to set a goal, a date/event by which time I want to have it running. That's helped to "light a fire under my rear" much more so than the amorphous, undefined "I want to get this thing running one day" idea - but you probably don't need me to suggest that to you...