lsa blower swap?
#61
Teching In
iTrader: (2)
Join Date: Dec 2006
Location: Los Angeles, CA
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
lsa blower swap?
So here's where I'm at. Fit the S&P AC bracket and ran into an issue with their supercharger tensioner bracket.
The bracket is easy to modify, but the tensioner once bolted to the bracket is way to close to the lower AC idler for my liking.
So I looked back in the S&P catalog thinking that it was right and discovered they had designed the tensioner bracket differently for the high AC mount.
I called S&P and them seem to think that it's the same (which it clearly isn't). I have sent them pictures and I'm waiting to hear back.
I believe the bracket can be modified to work, but the whole point of using their set-up was to not have to do that.....
The bracket is easy to modify, but the tensioner once bolted to the bracket is way to close to the lower AC idler for my liking.
So I looked back in the S&P catalog thinking that it was right and discovered they had designed the tensioner bracket differently for the high AC mount.
I called S&P and them seem to think that it's the same (which it clearly isn't). I have sent them pictures and I'm waiting to hear back.
I believe the bracket can be modified to work, but the whole point of using their set-up was to not have to do that.....
#62
Staging Lane
Join Date: May 2015
Location: San Tan Valley, AZ
Posts: 54
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the update.
That bracket is way too close.
The catalog picture is quite a bit different than what you have.
Hopefully you can get it worked out with them.
I'm glad someone is already going through trial and error for me. lol.
I'll be waiting.
That bracket is way too close.
The catalog picture is quite a bit different than what you have.
Hopefully you can get it worked out with them.
I'm glad someone is already going through trial and error for me. lol.
I'll be waiting.
#63
Kwik is working on a low mount for a Sanden "microcompressor" that would work on the vette spacing, and not impact the supercharger belt. Being a smaller compressor they are thinking it will clear the motor mounts and cross member... They're test fitting this week.
I'm hoping to get my hands on it next week and my installer can make it work.
I'm hoping to get my hands on it next week and my installer can make it work.
#64
Staging Lane
Join Date: May 2015
Location: San Tan Valley, AZ
Posts: 54
Likes: 0
Received 0 Likes
on
0 Posts
I looked at kwik's stuff, and considered it, but my biggest issue is the choices of engine mounts for an LS in my car, and the way the factory mounts are set up. They all leave me with mere inches to work with. Best choice is a high mount for me.
#67
Staging Lane
Join Date: May 2015
Location: San Tan Valley, AZ
Posts: 54
Likes: 0
Received 0 Likes
on
0 Posts
Could you get me the S&P part#s involved?
I'm still a ways out from installing, but I might just buy these before they suddenly become unavailable.
#68
Teching In
iTrader: (2)
Join Date: Dec 2006
Location: Los Angeles, CA
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
lsa blower swap?
They're pretty old school over there so no part numbers. Talk to James Armer and ask for the LSA tensioner kit and 50's high mount AC to go with it. Make sure you mention the revised tensioner bracket. Remember you have to run the LSA/LS3 water pump for the mounting bosses for the tensioner
#69
Staging Lane
Join Date: May 2015
Location: San Tan Valley, AZ
Posts: 54
Likes: 0
Received 0 Likes
on
0 Posts
They're pretty old school over there so no part numbers. Talk to James Armer and ask for the LSA tensioner kit and 50's high mount AC to go with it. Make sure you mention the revised tensioner bracket. Remember you have to run the LSA/LS3 water pump for the mounting bosses for the tensioner
I actually picked up a used but super low mile LS3 water pump from the classifieds on here a few days ago.
Do you have another build thread for your car? I'd love to see the build on it.
#71
Staging Lane
Join Date: May 2015
Location: San Tan Valley, AZ
Posts: 54
Likes: 0
Received 0 Likes
on
0 Posts
#72
Teching In
iTrader: (2)
Join Date: Dec 2006
Location: Los Angeles, CA
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
lsa blower swap?
I've spoken to several tuners in regards to my build and using the 411 pcm. Everyone says no problem using it and I should be able to use the lsa 3 bar map sensor. I got my heads back from Wcch so I will be making big progress in the next couple of weeks. Stay tuned.
#73
TECH Addict
iTrader: (22)
My harness is using the 0411 PCM for this build, not much different from any other SC conversion. There are a few items that arent used:
Inlet vacuum
BARO
Boost bypass control solenoid
There is some rearranging of connectors, but nothing major. Planning DBC too. You can see the red/blue PCM connectors dangling below
Inlet vacuum
BARO
Boost bypass control solenoid
There is some rearranging of connectors, but nothing major. Planning DBC too. You can see the red/blue PCM connectors dangling below
#78
Teching In
iTrader: (2)
Kwik is working on a low mount for a Sanden "microcompressor" that would work on the vette spacing, and not impact the supercharger belt. Being a smaller compressor they are thinking it will clear the motor mounts and cross member... They're test fitting this week.
I'm hoping to get my hands on it next week and my installer can make it work.
I'm hoping to get my hands on it next week and my installer can make it work.
#80
Yep, got it in and installed last week. It required cutting a small pocket in the k-member and re-working the holley motor mounts back (in a 72 Camaro) but otherwise really works well. I don't think I could get a bigger compressor on a low mount at all, so short of a complete new front end this is the best option. Given I want to keep GM parts for the front end it's the only option.