Ignition coil harness
Thread Starter
TECH Apprentice
Joined: Sep 2012
Posts: 347
Likes: 66
From: Tucson, AZ
Ignition coil harness I am wiring up everything for my l33 swap in my 65 nova. I just realized I must have thrown out the old ignition coil harness when I took everything off to switch to Holley terminator x.
Where is the best place to get a new harness for each side? I see a lot of cheaper ones on eBay and Amazon but I'm not sure if they are any good. A lot of them also say relocation but I'm not sure what that means. I will be running my coils in the stock truck location.
Any help or advice would be greatly appreciated. Thanks!
Where is the best place to get a new harness for each side? I see a lot of cheaper ones on eBay and Amazon but I'm not sure if they are any good. A lot of them also say relocation but I'm not sure what that means. I will be running my coils in the stock truck location.
Any help or advice would be greatly appreciated. Thanks!
Relocation means that they are located off the valves covers. Maybe hidden somewhere or mounted on the fenders. The acdelco number is 357a they are kind of expensive usually around 70 plus bucks a side. Just type the number in google and shop around. I tend to find the best deals with free shipping on eBay
TECH Senior Member
Joined: Jun 2016
Posts: 22,291
Likes: 3,616
From: Central Cal.
Thread Starter
TECH Apprentice
Joined: Sep 2012
Posts: 347
Likes: 66
From: Tucson, AZ
It looks like $80/side new or there are some sets on eBay used for $60/pair.
These are probably a bad idea right?
https://www.ebay.com/itm/2-For-GM-Ig...-127632-2357-0
These are probably a bad idea right?
https://www.ebay.com/itm/2-For-GM-Ig...-127632-2357-0
TECH Senior Member
Joined: Jun 2016
Posts: 22,291
Likes: 3,616
From: Central Cal.
It looks like $80/side new or there are some sets on eBay used for $60/pair.
These are probably a bad idea right?
https://www.ebay.com/itm/2-For-GM-Ig...-127632-2357-0
These are probably a bad idea right?
https://www.ebay.com/itm/2-For-GM-Ig...-127632-2357-0
Trending Topics
Teching In
Joined: Aug 2021
Posts: 1
Likes: 0
Hi....they are in grouping on the harness........unless the linger is screwed up than its lovely self illustrative. They are spread out each 3 inches or so. Fair plug them in to their comparing area relative to the tackle. Did you expel the linger from the difficult plastic plate they are in?
https://www.7pcb.com/
https://www.7pcb.com/
Last edited by BriggTrim; Oct 14, 2021 at 11:06 AM.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo TECH Senior Member
Joined: Jun 2016
Posts: 22,291
Likes: 3,616
From: Central Cal.
hi....they are in grouping on the harness........unless the linger is screwed up than its lovely self illustrative. They are spread out each 3 inches or so. Fair plug them in to their comparing area relative to the tackle. Did you expel the linger from the difficult plastic plate they are in?
