Mark's LS1 2nd Gen Camaro build
#41
11 Second Club
Thread Starter
Join Date: Mar 2008
Location: New Westminster, B.C., Canada
Posts: 445
Likes: 0
Received 1 Like
on
1 Post
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
OK, so the LH8 pan was not ideal for my car. I posted it on craigslist and sold it the next day at only a $55 loss. The issue I had was steering interference. The LH8 pan may have worked if I jacked the motor up high enough, but the hood to throttle body clearance would have been limited. If you are following this thread then you know of my plans to pro-charge. This being said, I need all the space I can get to squeeze the charger under a stock hood.
SO...the mount set-up that works for me. I am using the trans-dapt ls1/sbc adapter plates, with a 1/2 inch spacer placed under the factory crossmember to mount plate. I am re-drilling the crossmember and shifting the mount rearward 1/4 to 1/2 inch. This allows good clearance for my F-body oil pan, steering , and alternator.
The LH8 Pan was better at the rear of the crossmember, but the sump sat lower than the crossmember (as low as 2" before jacking up the motor) and the front of the pan was deeper than the Fbody pan and hit the steering before being jacked up, and at that point I decided to use the F body pan as ground clearance is a big issue for me.
In conclusion, I recommend the F body pan. ( mine is from a '99 trans am )
SO...the mount set-up that works for me. I am using the trans-dapt ls1/sbc adapter plates, with a 1/2 inch spacer placed under the factory crossmember to mount plate. I am re-drilling the crossmember and shifting the mount rearward 1/4 to 1/2 inch. This allows good clearance for my F-body oil pan, steering , and alternator.
The LH8 Pan was better at the rear of the crossmember, but the sump sat lower than the crossmember (as low as 2" before jacking up the motor) and the front of the pan was deeper than the Fbody pan and hit the steering before being jacked up, and at that point I decided to use the F body pan as ground clearance is a big issue for me.
In conclusion, I recommend the F body pan. ( mine is from a '99 trans am )
#42
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I just got my 6.0 LQ4 home! Ive got and 80' camaro and you probably saved me some money on the pan subject
. Im probably going to use the same stuff since it works well for you.
Thanks for the info...keep us posted!
![Angel](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_angel.gif)
Thanks for the info...keep us posted!
Last edited by MrCheap; 05-19-2008 at 08:06 PM.
#43
Launching!
iTrader: (7)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Hi Mark. Nice looking project. I've got an LQ4 in my 81Z and used all fbody accessories and oil pan.
I'm in Cloverdale and if you need any help let me knowas my swap is done and running well.
Up untl now, I thought I was the only one with a LSX in a 2nd gen in the Lower Mainland of BC.
I'm in Cloverdale and if you need any help let me knowas my swap is done and running well.
Up untl now, I thought I was the only one with a LSX in a 2nd gen in the Lower Mainland of BC.
#44
11 Second Club
Thread Starter
Join Date: Mar 2008
Location: New Westminster, B.C., Canada
Posts: 445
Likes: 0
Received 1 Like
on
1 Post
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Good to meet ya Z! I'd like to pick your brain a little just to see how you went about doing your swap! in fact, pm me yer number and I'll give you a call sometime to discuss a couple things... cheers!
#45
11 Second Club
Thread Starter
Join Date: Mar 2008
Location: New Westminster, B.C., Canada
Posts: 445
Likes: 0
Received 1 Like
on
1 Post
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Well, I finally found someone to finish painting the car! Waiting for the flat deck right now to take it to his shop. After a bunch of research and emails, I got a hold of the guy who started the bodywork in the first place, and with a little begging, he decided to bench another project he was working on to complete mine! Yay.... continued....
#46
11 Second Club
Thread Starter
Join Date: Mar 2008
Location: New Westminster, B.C., Canada
Posts: 445
Likes: 0
Received 1 Like
on
1 Post
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
things are coming together ever so slowly.... anyway, here's a pic! built my own procharger mount kit, and as you can see the car is fully painted!
![Name: IMG_2700.jpg
Views: 3777
Size: 127.6 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664266d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2700.jpg)
Last edited by Marktainium; 11-21-2010 at 01:44 PM.
#47
Launching!
iTrader: (7)
Join Date: Aug 2007
Location: Austin, TX via Pottstown,PA
Posts: 287
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Sweet project! I had envisioned this for my 70 but have now decided that it will be strait-line only so no T-56
. I had a quick question however about your mounts. You say you are redrilling the crossmember to move the mount back 1/4-1/2 inch, by redrilling are you saying that you just elongated the factory holes on the crossmember and if not can you post a pic as I am easily confused. Thank you!
![Sad](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_sad.gif)
#48
11 Second Club
Thread Starter
Join Date: Mar 2008
Location: New Westminster, B.C., Canada
Posts: 445
Likes: 0
Received 1 Like
on
1 Post
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Sweet project! I had envisioned this for my 70 but have now decided that it will be strait-line only so no T-56
. I had a quick question however about your mounts. You say you are redrilling the crossmember to move the mount back 1/4-1/2 inch, by redrilling are you saying that you just elongated the factory holes on the crossmember and if not can you post a pic as I am easily confused. Thank you!
![Sad](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_sad.gif)
Since then I have remounted the engine and built myself a transmission crossmember with provisions for exhaust clearance.
#49
Staging Lane
iTrader: (6)
Join Date: May 2007
Location: hayward, Ca
Posts: 91
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
the lh8 pan wasnt working for me either... i was having problems getting my motor mount bolt holes to line up due to the pan hittin the subframe.. the motor would have had to be lifted waay too much and the trans tunnel would have had to be modified to make it work... i sold two lh8 pans with a loss of $80 each
#50
11 Second Club
Thread Starter
Join Date: Mar 2008
Location: New Westminster, B.C., Canada
Posts: 445
Likes: 0
Received 1 Like
on
1 Post
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Here'e my transmission crossmember. it's a 3 piece deal, took way too long to build, but thats the fun part, right?
![Name: IMG_2493.jpg
Views: 3775
Size: 81.8 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664267d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2493.jpg)
![Name: IMG_2493.jpg
Views: 3775
Size: 81.8 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664267d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2493.jpg)
![Name: IMG_2494.jpg
Views: 3720
Size: 80.4 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664268d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2494.jpg)
Last edited by Marktainium; 11-21-2010 at 01:46 PM.
#52
11 Second Club
Thread Starter
Join Date: Mar 2008
Location: New Westminster, B.C., Canada
Posts: 445
Likes: 0
Received 1 Like
on
1 Post
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Since I am supercharging I had to 'pin' my harmonic balancer. Here's how that went.
1. Took a chunk of tool steel and 'spun up' a guide tool on a friends lathe.
![Name: IMG_2680.jpg
Views: 3709
Size: 71.6 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664269d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2680.jpg)
2. Bolted it to the balancer.
![Name: IMG_2675.jpg
Views: 3664
Size: 47.4 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664270d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2675.jpg)
3. Took a brand new 1/4" drill bit and marked off with tape 5/8" depth.
![Name: IMG_2679.jpg
Views: 3698
Size: 38.9 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664271d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2679.jpg)
4. Drilled to depth, then removed Tool.
![Name: IMG_2674.jpg
Views: 3695
Size: 176.7 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664272d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2674.jpg)
5. Cut 1/2" off of the chuck end of the 1/4" drill bit.
![Name: IMG_2682.jpg
Views: 3734
Size: 50.6 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664273d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2682.jpg)
6. Inserted 1/2" drill bit piece into crank pin hole.
![Name: IMG_2683.jpg
Views: 3830
Size: 125.2 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664274d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2683.jpg)
7. Re-assemble and enjoy!
1. Took a chunk of tool steel and 'spun up' a guide tool on a friends lathe.
![Name: IMG_2680.jpg
Views: 3709
Size: 71.6 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664269d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2680.jpg)
2. Bolted it to the balancer.
![Name: IMG_2675.jpg
Views: 3664
Size: 47.4 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664270d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2675.jpg)
3. Took a brand new 1/4" drill bit and marked off with tape 5/8" depth.
![Name: IMG_2679.jpg
Views: 3698
Size: 38.9 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664271d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2679.jpg)
4. Drilled to depth, then removed Tool.
![Name: IMG_2674.jpg
Views: 3695
Size: 176.7 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664272d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2674.jpg)
5. Cut 1/2" off of the chuck end of the 1/4" drill bit.
![Name: IMG_2682.jpg
Views: 3734
Size: 50.6 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664273d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2682.jpg)
6. Inserted 1/2" drill bit piece into crank pin hole.
![Name: IMG_2683.jpg
Views: 3830
Size: 125.2 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664274d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2683.jpg)
7. Re-assemble and enjoy!
![Name: IMG_2122.jpg
Views: 3651
Size: 93.0 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664275d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2122.jpg)
Last edited by Marktainium; 11-21-2010 at 01:52 PM.
#54
11 Second Club
Thread Starter
Join Date: Mar 2008
Location: New Westminster, B.C., Canada
Posts: 445
Likes: 0
Received 1 Like
on
1 Post
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
The whole point of doing a project car is building it. I'm not rich either, so alot of it comes down to if I don't build it I can't buy it. Well, really, lets put it this way, if I could afford to buy the trick parts, I probably would. Until I win the Lotto, this is it. (Even if I was rich, I would still make my parts, only I wouldn't have a pesky day job to get in the way!)
#55
11 Second Club
Thread Starter
Join Date: Mar 2008
Location: New Westminster, B.C., Canada
Posts: 445
Likes: 0
Received 1 Like
on
1 Post
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
GOT IT IN!
Hopefully this isn't another test fitting! Got the LS2 into it's mount and all bolted up. It's a tight fit, especially between the 'charger and the upper control arm. But there is space. Time to start the plumbing.
![Name: IMG_2722.jpg
Views: 3825
Size: 146.2 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664276d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2722.jpg)
![Name: IMG_2723.jpg
Views: 3743
Size: 119.8 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664277d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2723.jpg)
Hopefully this isn't another test fitting! Got the LS2 into it's mount and all bolted up. It's a tight fit, especially between the 'charger and the upper control arm. But there is space. Time to start the plumbing.
![Name: IMG_2722.jpg
Views: 3825
Size: 146.2 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664276d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2722.jpg)
![Name: IMG_2723.jpg
Views: 3743
Size: 119.8 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664277d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2723.jpg)
![Name: IMG_2724.jpg
Views: 3687
Size: 144.7 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664278d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2724.jpg)
Last edited by Marktainium; 11-21-2010 at 01:55 PM.
#56
TECH Fanatic
iTrader: (10)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Nice project man. It's always cool to see fellow LSx enthusiasts up here in Canada.
Awesome fab work, I'd love to have access to machines but right now it's just me and my MIG & anglegrinder
And it's funny to see someone building in a garage smaller than mine, didn't think it was possible!!
Would love to see this one day when it's finished, maybe by that day my LQ4 conversion will be finished too!!!
Awesome fab work, I'd love to have access to machines but right now it's just me and my MIG & anglegrinder
![Happy](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_stretch.gif)
Would love to see this one day when it's finished, maybe by that day my LQ4 conversion will be finished too!!!
#58
11 Second Club
Thread Starter
Join Date: Mar 2008
Location: New Westminster, B.C., Canada
Posts: 445
Likes: 0
Received 1 Like
on
1 Post
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Cleaned up the tranny a bit and installed it tonight. The new crossmember worked perfectly, really happy about that! Here's a few pics. Note the clearance between the hood and intake, that shot is with the hood closed!
- all this is being done in a 10 x 20 garage too!!!
![Name: IMG_2760.jpg
Views: 3839
Size: 114.4 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664279d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2760.jpg)
![Name: IMG_2766.jpg
Views: 3704
Size: 102.5 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664280d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2766.jpg)
![Name: IMG_2763.jpg
Views: 3704
Size: 73.3 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664281d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2763.jpg)
![Name: IMG_2768.jpg
Views: 3683
Size: 95.2 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664282d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2768.jpg)
- all this is being done in a 10 x 20 garage too!!!
![Name: IMG_2760.jpg
Views: 3839
Size: 114.4 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664279d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2760.jpg)
![Name: IMG_2766.jpg
Views: 3704
Size: 102.5 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664280d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2766.jpg)
![Name: IMG_2763.jpg
Views: 3704
Size: 73.3 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664281d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2763.jpg)
![Name: IMG_2768.jpg
Views: 3683
Size: 95.2 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664282d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2768.jpg)
![Name: IMG_2773.jpg
Views: 3699
Size: 118.2 KB](https://ls1tech.com/forums/attachments/conversions-swaps/664283d1501791986-mark-s-ls1-2nd-gen-camaro-build-img_2773.jpg)
Last edited by Marktainium; 11-21-2010 at 01:57 PM.
#59
TECH Resident
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Cleaned up the tranny a bit and installed it tonight. The new crossmember worked perfectly, really happy about that! Here's a few pics. Note the clearance between the hood and intake, that shot is with the hood closed!
- all this is being done in a 10 x 20 garage too!!!
- all this is being done in a 10 x 20 garage too!!!
![Nod](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_nod.gif)
#60
TECH Fanatic
iTrader: (9)
Join Date: Aug 2007
Location: Rocky Mtn thin air & snow...
Posts: 1,237
Likes: 0
Received 1 Like
on
1 Post
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Cool](https://ls1tech.com/forums/images/icons/icon6.gif)
Originally Posted by Marktainium
Here's my transmission crossmember. it's a 3 piece deal, took way too long to build, but that's the fun part, right?
![Icon Lol](https://ls1tech.com/forums/images/smilies2/icon_lol.gif)
Anyway, great job, I'm enjoying this build.
![Mr. Cool](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_cool.gif)