13.56 @ 103 Bolt on LT1 good or bad?
#1
TECH Enthusiast
Thread Starter
Join Date: Mar 2009
Location: RI
Posts: 722
Likes: 0
Received 0 Likes
on
0 Posts
13.56 @ 103 Bolt on LT1 good or bad?
60' ... 2.16
1/8 ... 8.78
MPH....82.21
1/4 ... 13.561
MPH ... 103.04
the car MPH 103.52 on another run with a 2.205 60' pass
pass made on NT555, not DR
i know that 60' is killing me, but what time is possible if i get that 60' down?
what would it take to get 12s they way i am now? mods in sig
1/8 ... 8.78
MPH....82.21
1/4 ... 13.561
MPH ... 103.04
the car MPH 103.52 on another run with a 2.205 60' pass
pass made on NT555, not DR
i know that 60' is killing me, but what time is possible if i get that 60' down?
what would it take to get 12s they way i am now? mods in sig
Trending Topics
#9
TECH Enthusiast
iTrader: (13)
Nice job for LT1 and bolt ons! Either poor track prep or u have some water left on the tires. with ur power level and comparing to what my previous A4 LT1's are basically the same, id drive around the water and do a quick dry burn out. had 28lbs on streets and dead hooked.
edit, i also agree with the posts above as far as going faster
edit, i also agree with the posts above as far as going faster
Last edited by z28241; 09-05-2012 at 09:31 PM.
#16
10 Second Club
iTrader: (5)
Join Date: Jan 2003
Location: Fort Worth, TX
Posts: 1,455
Likes: 0
Received 0 Likes
on
0 Posts
I had to go back to my old CamaroZ28 days for this
Stock stall.
60'____?
1/8____8.091_@80.33mph
1/4____12.948@102.26
With Midwest 3000 stall spinning.
60'____1.7
1/8____8.1_@_85.3MPH
1/4____12.86_@_105.2
Stock stall.
60'____?
1/8____8.091_@80.33mph
1/4____12.948@102.26
With Midwest 3000 stall spinning.
60'____1.7
1/8____8.1_@_85.3MPH
1/4____12.86_@_105.2
#18
TECH Resident
iTrader: (13)
Join Date: Aug 2007
Location: Wild West
Posts: 768
Likes: 0
Received 0 Likes
on
0 Posts
My Auto, 3.23, LT1 full weight with cold air/LT's/GMMG went 13.6 at 105.5. So you aren't too far off. Didn't have a ported TB, but did have a Madwolf tune. Runs were made with street tires and I ended up with a 2.2-2.3 60'
-Dustin-
-Dustin-
#19
TECH Junkie
iTrader: (31)
There have been many previous to me to give advice... Props to a good ET.
My Lt1 with bolt ons:
Madtuner tune
PaceSetter longtubes
2.5" Xpipe w/ 10series flowmasters
1.6roller rockers
SLP lid w/fram filter
4.10 gears
BFG drs
no spare or Jack
BMR sfc
Lakewood LCAs
Crappy auto zone clutch
12.98 @ 106 3004'DA
You are doing fine however it is time to drop some cash.....
My Lt1 with bolt ons:
Madtuner tune
PaceSetter longtubes
2.5" Xpipe w/ 10series flowmasters
1.6roller rockers
SLP lid w/fram filter
4.10 gears
BFG drs
no spare or Jack
BMR sfc
Lakewood LCAs
Crappy auto zone clutch
12.98 @ 106 3004'DA
You are doing fine however it is time to drop some cash.....