New Best @ Carlsbad
New Best @ Carlsbad Well I haven't had the car to the track since it was almost stock....so it was time to test all the mods.....ran on ET streets...car has no weight reduction and is on stock suspension (except for a Pro-Kit which is not helping traction).....mods are in sig.....2 best runs:
12.46 @ 109.48 - 1.80 60'
12.49 @ 109.19 - 1.83 60'
Well, I have a pulley sitting at home alnog with some fresh plugs and MSD wires, an Andy's ported TB on the way and I realize that I need some 3.73's real bad...these 2.73's are awful!
Congrats to Brandin and Jen, Rich, Rob, and Terry on new bests also! Good to see all of you F-body and vette guys and gals out there!
Big thanks again to Mark @ Andy's for everything! You da man!
Joe
<small>[ July 29, 2002, 12:47 PM: Message edited by: TITAN ]</small>
12.46 @ 109.48 - 1.80 60'
12.49 @ 109.19 - 1.83 60'
Well, I have a pulley sitting at home alnog with some fresh plugs and MSD wires, an Andy's ported TB on the way and I realize that I need some 3.73's real bad...these 2.73's are awful!
Congrats to Brandin and Jen, Rich, Rob, and Terry on new bests also! Good to see all of you F-body and vette guys and gals out there!
Big thanks again to Mark @ Andy's for everything! You da man!
Joe
<small>[ July 29, 2002, 12:47 PM: Message edited by: TITAN ]</small>
Re: New Best @ Carlsbad Congrats Joe on your new best! Those times are hauling for those mods, expecially with those 2.73's. Put some 3.73's on there along with your pulley and TB and you'll be beating all the cam/header M6 guys. Thanks again for letting drive your car, it was first time ever driving an A4 F-Body.
Re: New Best @ Carlsbad Terry,
Not for a bit...I really would like to go 11's Stock Internal full weight (wouldn't that be a feat out here!), so I'll probably do an AAP ported TB, FTRA, pulley, 3.73's ,some custom tuning, long tubes and some skinnies.....we'll see if I can get a nice DA day this fall and pull it off....after that...we'll see....
Joe
Not for a bit...I really would like to go 11's Stock Internal full weight (wouldn't that be a feat out here!), so I'll probably do an AAP ported TB, FTRA, pulley, 3.73's ,some custom tuning, long tubes and some skinnies.....we'll see if I can get a nice DA day this fall and pull it off....after that...we'll see....
Joe
Trending Topics
TECH Enthusiast
Joined: Nov 2001
Posts: 652
Likes: 0
From: Newport Coast, Ca
Re: New Best @ Carlsbad Titan,
Congrats on those Times man! I have yet to see a car with as little mods as you have runnin mid 12's like that. (especially at Carlsbad) You have a really strong setup. Do the lil things like an asp pulley, TB, and some 3.73's and you'll see low 12's, high 11's easy.
Congrats on those Times man! I have yet to see a car with as little mods as you have runnin mid 12's like that. (especially at Carlsbad) You have a really strong setup. Do the lil things like an asp pulley, TB, and some 3.73's and you'll see low 12's, high 11's easy.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Re: New Best @ Carlsbad Wow that is great with 2.73's!
I'd do the ported TB and the pulley which should take like an hour to install both and then see what kind of gain you get!
I'd do the ported TB and the pulley which should take like an hour to install both and then see what kind of gain you get!
Re: New Best @ Carlsbad Thanks guys...
PSJ - That's exactly what I'm going to do, along with some MSD wires and NGK plugs (I get mutliple misfore codes from time to time)...
Joe
PSJ - That's exactly what I'm going to do, along with some MSD wires and NGK plugs (I get mutliple misfore codes from time to time)...
Joe