orangeapeel

iTrader: (18)

first of all you need to get a heavy duty zip tie. Next wrap it around his driveshaft.

Datzneat

iTrader: (4)

I do that to my driveshaft sometimes. Feels good.... o wait...nevermind

Sarahgto

lol funny comments.. Im going to dyno the car to see what it has but yeah get tire and gears because if i spray on him he would say yeah but you need spray to beat me. So im trying to show him you dont need to pay top dollar to make your car fast i can do it with budget parts and stock heads with a little stuff dont to them. I know the camaro has power off the heads because i went to the track with drs and snap the driveshaft in half. Look like it twisted and snap and i only tried to launch the car at 2500 rpm so i dont know what it runs because that was the first pass.

victor111262

4.10 or 4.11 on the rear and some tires and your set u should eat that ****

Theblacknightls1

iTrader: (1)

I have the same mods..Was the hand porter good and are you dynoing the car at the same place??

Theblacknightls1

iTrader: (1)

I agree with victor 410s and you got him easy

odarabla

iTrader: (1)

Actually the heads will make a difference.

Theblacknightls1

iTrader: (1)

Yeah heads are where you get your power from but both sets of heads are good. BUT his should flow better and i think you have a better cam..lol ha

Defined1983

iTrader: (20)

i'd go with the gears. inexpensive quick mod that will help you out a lot

09camaro383

iTrader: (2)

I agree with SOMbitch those numbers are high for those mods!! I have to see it to believe it!!

Detoxx03

iTrader: (14)

If you do a dig make sure you have some et streets or nt05r's cause w/ his power the 555r's are gonna be that great or if you do a roll make sure your in the correct powerband

bp944

iTrader: (4)

LT1porsche has a good point. Even a small shot will give you the edge.

Theblacknightls1

iTrader: (1)

No excuses all motor!! Just put gears and leave on him. That combo is dynoed proven to be great prc 2.5 mil to 59cc are very good heads and flow over 300cfm and raise compression with a cam that has 588 lift and suporting mods..Yeah i can believe 430+rwhp But dyno numbers arnt everything

Sarahgto

Yeah i know, I was their when it dynoed 432rwhp.. First it dynoed 415 but with 85% trottle and than they kept running it like 4 more passes and it went from 428 to 430 431 432 and than guy said thats the most i can get out of it saftley. But i know its just numbers.. He just been so cocky ever since. He spent 5000 for everything brand new. All his bolt ons plus heads and cam. So i rub it in his face and he tells me well that ss is not going to make over 400rwhp on stock heads.. So i laugh.. He really dosnt even know what he has Or anything about what he has. Puting 410s on the car and hopfully were running Thursday.

victor111262

yes those 4.10 should do it

DeanJ

iTrader: (6)

Spray that bitch. He wont know what hit him.

Red99TA

iTrader: (11)

Sounds like a dumbass to me. I made the same numbers almost (427RWHP) on my last Trans Am which was with a 233/239 TSP cam, FAST intake/TB, LTs/ORY/Magnaflow, and UD pulley oh and STOCK HEADS!

Detoxx03

iTrader: (14)

Agreed

MPFD

iTrader: (5)

if you guys are buddies, and you put a bitch slap on him, he's gonna find out you sprayed him and call BS. I bet its a close race. If you do a gear your gonna need drag radials too. If you do spray him, use just enough to maybe put a car on him, that way he won't suspect....

Theblacknightls1

iTrader: (1)

Mpfd, yup I agree also