Ws6 turbo drag car partout
#1
9 Second Club
Thread Starter
iTrader: (22)
Join Date: Mar 2008
Location: Lancaster,Pa.
Posts: 777
Likes: 0
Received 0 Likes
on
0 Posts
Ws6 turbo drag car partout
Decided it's time to sell off my car and parts and start a new venture. Just don't have the funds or justification to finish this again.
Please PM me for best response....don't always check this page
Most of the parts have only 30 passes on them
MWC 9" braced and shortened 3" per side.....powder coated black and drain and fill caps installed
- Strange nodular iron center with billet carrier
- 3.25 gear with spool
-35 spline axles
-MWC short torque arm with crossmember mount
-MWC trans mount for t56 or th400
-MWC drag bar
-Strange drag brakes
-Strange driveshaft correct length for th400 to 9"
............pending......Will not ship
2- Billet specialties 15x10 wheels with 4.5" backspace and MT 325/50/15 drag radials mounted on them. Is the correct offset for this rear.........pending
-Big Stuff 3 with DAI and 2 harnesses...(when I bought it they sent me two for some reason).......$1800
-1 Kirkey seat with grey cover..... $100
Build thread...https://ls1tech.com/forums/forced-in...ust-build.html
Please PM me for best response....don't always check this page
Most of the parts have only 30 passes on them
MWC 9" braced and shortened 3" per side.....powder coated black and drain and fill caps installed
- Strange nodular iron center with billet carrier
- 3.25 gear with spool
-35 spline axles
-MWC short torque arm with crossmember mount
-MWC trans mount for t56 or th400
-MWC drag bar
-Strange drag brakes
-Strange driveshaft correct length for th400 to 9"
............pending......Will not ship
2- Billet specialties 15x10 wheels with 4.5" backspace and MT 325/50/15 drag radials mounted on them. Is the correct offset for this rear.........pending
-Big Stuff 3 with DAI and 2 harnesses...(when I bought it they sent me two for some reason).......$1800
-1 Kirkey seat with grey cover..... $100
Build thread...https://ls1tech.com/forums/forced-in...ust-build.html
Last edited by 1fast bird; 01-06-2013 at 10:33 AM.
Trending Topics
#8
TECH Apprentice
iTrader: (8)
Join Date: Apr 2009
Location: Orange county, ny
Posts: 365
Likes: 0
Received 0 Likes
on
0 Posts
The 6.0 block aluminum or cast iron ?
How much for the the whole bottom end pistons, rods and block?
Is everything machined and ready to be installed or does it need further machine work? Does it come with main caps and rods bearings? mileage on the block?
Basically what else would I need to make a complete short block
Please PM me the info, about 3 hours from lancaster
How much for the the whole bottom end pistons, rods and block?
Is everything machined and ready to be installed or does it need further machine work? Does it come with main caps and rods bearings? mileage on the block?
Basically what else would I need to make a complete short block
Please PM me the info, about 3 hours from lancaster
Last edited by MyFirstLS1; 11-05-2012 at 07:03 PM.
#10
9 Second Club
Thread Starter
iTrader: (22)
Join Date: Mar 2008
Location: Lancaster,Pa.
Posts: 777
Likes: 0
Received 0 Likes
on
0 Posts
The 6.0 block aluminum or cast iron ?
How much for the the whole bottom end pistons, rods and block?
Is everything machined and ready to be installed or does it need further machine work? Does it come with main caps and rods bearings?
Basically what else would I need to make a complete short block
How much for the the whole bottom end pistons, rods and block?
Is everything machined and ready to be installed or does it need further machine work? Does it come with main caps and rods bearings?
Basically what else would I need to make a complete short block