Anybody w/APS TT kit come on in
Anybody w/APS TT kit come on in Does anybody have any dyno #'s on the upgraded kit on a stroker motor? Or what is everybody making with this kit on any set up?This is going on a 6spd 98 street camaro. Does anybody have there frt bumper cut out (where the billet grille goes)so you can see the IC or does the IC sit to far in the back to see it? If so please post up any pics. Maybe under car pics so I can see if it can be done. I want to be able to see the FMIC. I know the IC comes blk but I will get it painted or powder coated. Which would be better painting it or powder coating? Thanks
Last edited by jeremym; Feb 15, 2009 at 11:17 PM.
for the APS kit, the intercooler sits angled and runs behind the bumper support so you will not be able to see it.
__________________
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
__________________
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
Don't think you want to powder coat a air to air intercooler. You want the core to be able to shed heat quickly. PC although not a heat retention coating is thick and will no doubt take away from the efficiency of the core itself.
Best only have a thin layer of paint on it or bare aluminum.
Best only have a thin layer of paint on it or bare aluminum.
Trending Topics
My camaro with a 402 stroker @ 13.5 psi did 730rwhp. That was the old stock turbos and then they actaully went out after that pull. If your thinking of upgrading them, do it now, not after they go out.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo I ordered the 427 Upgraded kit. Doesnt that kit have the good turbos? Is there another upgrade I missed?
APS/Pics I base/cleared my intercooler to match my intake after I installed the BOV 's in the intercooler neck!( You can see it allright)! LOL and also redid the black APS rad /intercooler sheild and it looks 100% better then that black one APS did! I'll post new pics of that later. Someone can post these if they want! I never did it yet ,Sorry
http://s243.photobucket.com/albums/f.../APs%20Engine/
http://s243.photobucket.com/albums/f.../APs%20Engine/
I base/cleared my intercooler to match my intake after I installed the BOV 's in the intercooler neck!( You can see it allright)! LOL and also redid the black APS rad /intercooler sheild and it looks 100% better then that black one APS did! I'll post new pics of that later. Someone can post these if they want! I never did it yet ,Sorry
http://s243.photobucket.com/albums/f.../APs%20Engine/
http://s243.photobucket.com/albums/f.../APs%20Engine/
very nice detail on the car for sure, its clean as hell i dont think i could drive it after all that work
my car is more like "less is more" thing going on
who did the work to get those BOV in the side of the innercooler like that?
very nice trans as well im thinking of getting one down the road
i have some pics of mine on my profile if you want to see them its turning in to more of a race car than a street car LOL
You got the upgraded kit so its hard to say if you are going to have any problems with your turbos. Just about every person on here has the standard kit. There have been several dynos thru the months on the standard kit. Most have not pushed them past about 12psi due to that inlet tube collapsing thing . You also should not have that problem on your upgraded kit but again a bit early to say.
I think there was one dyno of the upgraded kit seem to remember think some shop has already done it. You should be able to get to 1000rwhp no problem with your kit. About 1100rwhp should be about the max on an m6. What clutch are you going with again?
And better plan on tranny upgrade as well.
So Kwikkar what is your update. Its been months and months. So is your car done and ready soon for some dynos ,etc. Did that company put in 3 inch inlet turbos for you. Are they still tweaked mits 20gs or did they somehow put garetts in there or something else?
I think there was one dyno of the upgraded kit seem to remember think some shop has already done it. You should be able to get to 1000rwhp no problem with your kit. About 1100rwhp should be about the max on an m6. What clutch are you going with again?
And better plan on tranny upgrade as well.
So Kwikkar what is your update. Its been months and months. So is your car done and ready soon for some dynos ,etc. Did that company put in 3 inch inlet turbos for you. Are they still tweaked mits 20gs or did they somehow put garetts in there or something else?
Here is good thread and closer to your upgraded turbos rated airflow of 65 pounds per minute. This guy has tested 60 pound per minute ones. Was hoping he will have some more updates for us.
This car is just a 346. The main advantage to the bigger motors is you should be able to get same power levels as the smaller motor at lower boost and of course have more power off boost and more torque and quicker spool up.
https://ls1tech.com/forums/forced-in...800-901-a.html
Also this car ran two cutouts in front of the ypipe and full normal exhaust. So no real need for true duals.
This car is just a 346. The main advantage to the bigger motors is you should be able to get same power levels as the smaller motor at lower boost and of course have more power off boost and more torque and quicker spool up.
https://ls1tech.com/forums/forced-in...800-901-a.html
Also this car ran two cutouts in front of the ypipe and full normal exhaust. So no real need for true duals.
The company did put 3 inch inlets on the turbos. I'll post up pictures next time I go work on the car. Well the car is not done and what was done now has to be redone b/c it wasn't installed right. IE: BMR TA on a moser 12 bolt. Need to do the brakes, Drive Shaft, install turbos, exhaust, ETC.... It should be a few more weeks before I see the dyno.
man i dont know if i like it or hate it LOL
very nice detail on the car for sure, its clean as hell i dont think i could drive it after all that work
my car is more like "less is more" thing going on
who did the work to get those BOV in the side of the innercooler like that?
very nice trans as well im thinking of getting one down the road
i have some pics of mine on my profile if you want to see them its turning in to more of a race car than a street car LOL
very nice detail on the car for sure, its clean as hell i dont think i could drive it after all that work
my car is more like "less is more" thing going on
who did the work to get those BOV in the side of the innercooler like that?
very nice trans as well im thinking of getting one down the road
i have some pics of mine on my profile if you want to see them its turning in to more of a race car than a street car LOL
Trust me !!!I was scarred as **** drilling the holes in the sides of this intercooler LOL I measured and marked 20 times before i started drilling LOL
She's my baby! If there was just a little fur around her CME lips LOL
i feel you man its clean as hell and you did a realy good job on it.
i want to make 800 to1000rwhp someday with mine
im looking to put a 50mm BOV before the TB with mine. i also want to move the FMIC forward and down to make more room for the RAD to get more air and more space to put my meth kit,BOV and IAT in that pipe in between the TB and the innercooler
i want to make 800 to1000rwhp someday with mine
im looking to put a 50mm BOV before the TB with mine. i also want to move the FMIC forward and down to make more room for the RAD to get more air and more space to put my meth kit,BOV and IAT in that pipe in between the TB and the innercooler
http://www.exoticperformanceplus.com...Car.php?car=39
This is the standard APS kit, but I have a lot of pictures here. Bob
This is the standard APS kit, but I have a lot of pictures here. Bob
Be Cool i feel you man its clean as hell and you did a realy good job on it.
i want to make 800 to1000rwhp someday with mine
im looking to put a 50mm BOV before the TB with mine. i also want to move the FMIC forward and down to make more room for the RAD to get more air and more space to put my meth kit,BOV and IAT in that pipe in between the TB and the innercooler
i want to make 800 to1000rwhp someday with mine
im looking to put a 50mm BOV before the TB with mine. i also want to move the FMIC forward and down to make more room for the RAD to get more air and more space to put my meth kit,BOV and IAT in that pipe in between the TB and the innercooler