Boost reference location for waste gate.. what is the final answer?
#21
I would reference the manifold as long as the reference line wasn't a mile long. The longer your reference line is, the less response it will have.
But I am also a firm believer in the "Reference what the motor sees" theory.
But I am also a firm believer in the "Reference what the motor sees" theory.
#22
manifold, had a hell of time getting mine tuned when i had it hooked up to compressor. boost was falling off bad on the top end. moved it to the manifold and problem solved. this was recommended by the wastegate company. i must be loosing a lot of psi thru ebay intercooler. what the turbo is putting out and whats getting to manifold is a big difference.
#23
manifold, had a hell of time getting mine tuned when i had it hooked up to compressor. boost was falling off bad on the top end. moved it to the manifold and problem solved. this was recommended by the wastegate company. i must be loosing a lot of psi thru ebay intercooler. what the turbo is putting out and whats getting to manifold is a big difference.
#25
My plan is to use the compressor housing for the wastegate. It's supposed to be more responsive, it won't put a vacuum on the wastegate, and the boost at the compressor housing will be greater than in the manifold, so it should be a little safer.
#26
Like others have said I also reference directly off the compressor housing to the bottom of the gate.
I also tap the truboosts boost control solenoid into the compressor housing so that it gets higher psi sooner to the top of the gate to help keep it closed and spook faster.
The guage/controller reads off actual manifold psi levels so when you actually see say 10# at the motor the controller will start to let the wg open.
I also tap the truboosts boost control solenoid into the compressor housing so that it gets higher psi sooner to the top of the gate to help keep it closed and spook faster.
The guage/controller reads off actual manifold psi levels so when you actually see say 10# at the motor the controller will start to let the wg open.
#28
If I were to run wastegate spring only and no mbc/ebc I would reference off the intake manifold personally. That way the gate doesn't start to crack until the motor sees the boost.
And to the ppl that say the gate shouldn't and isn't made to see vacuum just put a one way check valve inline. Could use the same one most ppl use between the valley cover and manifold to keep boost out of the crank case and still maintain pcv under part throttle.
And to the ppl that say the gate shouldn't and isn't made to see vacuum just put a one way check valve inline. Could use the same one most ppl use between the valley cover and manifold to keep boost out of the crank case and still maintain pcv under part throttle.
#29
3X Vote
Wastegate = compressor housing
BOV & Boost Gauge = Intake manifold
Then just make a few 'full boost' runs (with the wife reading the boost gauge) to know how to tweek (open or closed) the manual controller...
BOV & Boost Gauge = Intake manifold
Then just make a few 'full boost' runs (with the wife reading the boost gauge) to know how to tweek (open or closed) the manual controller...
#30
If I were to run wastegate spring only and no mbc/ebc I would reference off the intake manifold personally. That way the gate doesn't start to crack until the motor sees the boost.
And to the ppl that say the gate shouldn't and isn't made to see vacuum just put a one way check valve inline. Could use the same one most ppl use between the valley cover and manifold to keep boost out of the crank case and still maintain pcv under part throttle.
And to the ppl that say the gate shouldn't and isn't made to see vacuum just put a one way check valve inline. Could use the same one most ppl use between the valley cover and manifold to keep boost out of the crank case and still maintain pcv under part throttle.
Dont put a check valve on your reference line, you would be trapping pressurized air in the line and holding the gate open.
I personnally use the compressor discharge port for the bottom of the gate and use a boost controller to add pressure to the top of the gate. Works great
#31
Dont put a check valve on your reference line, you would be trapping pressurized air in the line and holding the gate open.
I personnally use the compressor discharge port for the bottom of the gate and use a boost controller to add pressure to the top of the gate. Works great
I personnally use the compressor discharge port for the bottom of the gate and use a boost controller to add pressure to the top of the gate. Works great
It was just a thought on the check valve for the ppl saying the gate shouldn't see vacuum. Haven't done it but seems like it would work fine keeping vacuum off the diaphragm. Atleast on a tial since I know those vent.
#32
If your running wastegate spring only no controller at all and the top port is open on the gate it acts as a vent. Atleast on the tial it does.
It was just a thought on the check valve for the ppl saying the gate shouldn't see vacuum. Haven't done it but seems like it would work fine keeping vacuum off the diaphragm. Atleast on a tial since I know those vent.
It was just a thought on the check valve for the ppl saying the gate shouldn't see vacuum. Haven't done it but seems like it would work fine keeping vacuum off the diaphragm. Atleast on a tial since I know those vent.
#33
correct, the top port is sealed from the bottom, otherwise the boost reference would fly right through the gate and do nothing. the top port is there if you want to put additional pressure on top of the gate to hold it closed for more boost or whatever.
and yes the one way check valve would hold the gate open until it bled down and you would have terrible spool
and yes the one way check valve would hold the gate open until it bled down and you would have terrible spool