Projected horsepower
#701
TECH Resident
Thread Starter
10 an bungs welded to valve covers
Dual 525 huron speed pumps installed, fairly simple just used my same wires i already had ran. It came with the pins and plug so all i had to do was pin the wires in the plug.
Huron speed stepping there game up, i know the old style you had to put your stock fuel level sender on. This one came with it already installed
Everything bolted and riveted
The following 3 users liked this post by Tommy42088:
#703
TECH Resident
Thread Starter
#704
TECH Resident
Thread Starter
Changed from the bs spacer the kit came with to this ict bilet plate
10 an to valve covers
Back to catch can
Pumps are in, 8an is much better, only thing left is to change the injectors but ill do that on the dyno and i have to put fresh oil. I also changed my plugs as my tuner wanted to to tighten up my gap to 20
#705
TECH Resident
Thread Starter
I also have to pull the tranny again because for some reason my rear main seal blew again and my tuner said it was the way I had my catch can installed. Said it was causing to much pressure in the crankcase. No biggie though, we will put it on the lift this weekend and slap that seal on and stick the injectors in and get it back on the dyno
Update, so see how the sensor is vertical instead of horizontal. That didnt work out well for me, the truck always thougjt it was full of gas and even taking it out the truck and holding it upright the float was to heavy to let the sensor even go to the empty position so i cut the 2 rivets out and turned the sensor to an upright position like the factory unit and i had to drill hold in the bracket and lower it down for it to read accurately once i did that.
Update, so see how the sensor is vertical instead of horizontal. That didnt work out well for me, the truck always thougjt it was full of gas and even taking it out the truck and holding it upright the float was to heavy to let the sensor even go to the empty position so i cut the 2 rivets out and turned the sensor to an upright position like the factory unit and i had to drill hold in the bracket and lower it down for it to read accurately once i did that.
The following users liked this post:
Tommy42088 (07-02-2024)
#707
TECH Resident
Thread Starter
That's exactly what I did, welded 10an bungs to the valve covers and put a new catch can with a filter. I was to late tho. It already pushed on the seal. My dip stip is bolted down nice and tight so it wasnt coming out. It has a steady drip where the trans bolts to the block and my tuner told me thats what happened. I guess when we put it on the dyno and pushed it a little it had to let the pressure out some how.
The following users liked this post:
The BallSS (07-02-2024)
#708
TECH Resident
Thread Starter
#709
TECH Resident
Thread Starter
Put the truck on the lift yesterday at the tuners place and we changed the rear main seal and cleaned everything real well while we had it in the air and Crunk it while the trans was off and all was good so we put it back together and took it for a spin and fuel duty cycle dropped to 74 percent with just changing the pumps and running the 8an lines. Next week we're putting the bosch 210's in it and also putting fans on the trans cooler and changing the transmission lines to 6an lines to get rid of the bs hard line cut with rubber lines into the cooler then we're putting it back on the dyno. It did 50 mph burn out on 15 psi yesterday so it's pretty fun already.
The following 4 users liked this post by Tommy42088:
The following users liked this post:
The BallSS (07-08-2024)
#711
TECH Resident
Thread Starter
The following users liked this post:
The BallSS (07-08-2024)
#712
TECH Resident
Thread Starter
Patiently waiting on the new dyno numbers, went ahead and changed the transmission lines to 6an while I was at it and put tru cool fans on the transcooler considering I'm in Louisiana and the heat is ridiculous. I did end up getting the bosch 210 injectors to go along with the dual 525 pumps so I should have plenty fuel now.
The following 3 users liked this post by Tommy42088:
#714
TECH Resident
Thread Starter
me and you both, we have a dyno video from when it made the 670 before the new fuel system but I'll post the new ones when I get it back and thanks man, both arms are sleeved. Right is all demonic stuff with Matthew 7:13 and left is all angels and crosses and stuff like that with revelation 21:21
The following users liked this post:
The BallSS (07-22-2024)