anyone interested in 500ci forced inducted...with reliability?!
#21
Suspended Sponsor
Thread Starter
Join Date: Oct 2004
Location: Just outside of Palm Springs Ca.
Posts: 371
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
The sleeves are actually pressed through the deck plate and the gasket seals the top of the cylinder from any liquids getting into the cylinder, and the gasket below the plate seals the coolant inside the engine. As for the strength of the system, the deck plate is doweled to the block and the sleeves locate it as well, go to their website if you like and see the 4 cyl running 8.80's I believe from a front drive! Believe me that takes a lot of boost and they have the same number of studs securing the whole thing together. I really have no problem with the design, it has been computer designed and had extensive simulation to make sure it was worth building. I also don't think Judson from S.A.M. would waste his money on the expensive rotating assembly unless he thought it would work.
-Bryan
-Bryan
#25
10 Second Club
iTrader: (26)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
i have a question....does World use a deck plate as well with their 9.8".because if they dont then wouldnt itd be a little better and stronger since its cast like that as opposed to bolting down an additional piece to raise the deck height?im not knocking it as i wanna see what id do on pump gas NA,but just curious.
#26
Suspended Sponsor
Thread Starter
Join Date: Oct 2004
Location: Just outside of Palm Springs Ca.
Posts: 371
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
As far as oil consumption is concerned, I don't see why you think it will burn oil due to the stroke? I have never had a stroker use an ounce of oil more than a standard stroke, Oil consumption is based on the cylinder hone entirely, not the stroke length. As far as the deckplate being stronger or weaker than the one piece World block, I think it is a tossup. I really don't think either has an advantage in that sense as the mechanical lock from the dowels and head bolts being enlarged to 1/2" should be VERY secure. Also, remember the ERL block design is a 10.2" deck not 9.8" which is a large margin.
-Bryan
-Bryan
#27
TECH Veteran
Join Date: Dec 2001
Location: Ft. Lauderdale, FL, USA
Posts: 4,117
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by Race-Prep
As far as oil consumption is concerned, I don't see why you think it will burn oil due to the stroke? I have never had a stroker use an ounce of oil more than a standard stroke, Oil consumption is based on the cylinder hone entirely, not the stroke length. As far as the deckplate being stronger or weaker than the one piece World block, I think it is a tossup. I really don't think either has an advantage in that sense as the mechanical lock from the dowels and head bolts being enlarged to 1/2" should be VERY secure. Also, remember the ERL block design is a 10.2" deck not 9.8" which is a large margin.
-Bryan
-Bryan
#28
Suspended Sponsor
Thread Starter
Join Date: Oct 2004
Location: Just outside of Palm Springs Ca.
Posts: 371
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Stock ring packs are meant to keep oil consumption to a minimum, performance ring packs lean more towards power production and let a little get by due to their lower tension. Either way it should not be EVER any more than you currently have at 1qt to 1500 miles, that in itself is a bit high unless you have a drag race very low tension ring pack. If you would like to lower that usage, install a vacuum pump into the crankcase.
-Bryan
-Bryan
#29
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
hmmmmmmm big cc in a samll package! its an old trick but still makes me smile! can't wait to see what sort of results you guys can get from it! any idea of what a "creat motor" might cost??????
thanks Chris.
thanks Chris.
#31
Suspended Sponsor
Thread Starter
Join Date: Oct 2004
Location: Just outside of Palm Springs Ca.
Posts: 371
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
They will incliude a set of intake spacers and they end up being about 3/4" thick so they actually add runner volume and length to the intake track even further increasing torque production. E-mail us for pricing if you like.
-Bryan
-Bryan
#33
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
That FWD that Race-Prep mentions uses ERL block and that car runs 52 psi and has never leaked a gasket. The car has been 8.46 @ 174.
I'm really interested in this LS block. I personally have owned a .550 raised deck ERL Honda motor and I can assure you that their machining is top notch. I'm not sure how this block is, but my deck plate was press fit and then held down by the other studs. Honda guys have made around 950whp from 2.2 liter raised deck setups with rather simple setups.
What type of market is there for this motor?
I'm really interested in this LS block. I personally have owned a .550 raised deck ERL Honda motor and I can assure you that their machining is top notch. I'm not sure how this block is, but my deck plate was press fit and then held down by the other studs. Honda guys have made around 950whp from 2.2 liter raised deck setups with rather simple setups.
What type of market is there for this motor?
#34
TECH Resident
iTrader: (4)
Join Date: Jul 2004
Location: USA
Posts: 972
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by ddnspider
i have a question....does World use a deck plate as well with their 9.8".because if they dont then wouldnt itd be a little better and stronger since its cast like that as opposed to bolting down an additional piece to raise the deck height?im not knocking it as i wanna see what id do on pump gas NA,but just curious.
![Happy](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_stretch.gif)
Either way, it's good to see innovative products hit the market.
![Hail](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_hail.gif)