Twin T-61 Mustang Project Complete
#1
Twin T-61 Mustang Project Complete
This build was started at the shop about 18 months ago after the owner took out his previous engine with a supercharger.
Most of the engine work was done by the owner of the car (Ryan) and the fabrication and turbo work done by Joey at Excessive AutoSports. Most of the lay-out of the engine bay and running of wires, piping, etc. was done by Ryan and Joey. The intercooler are twins - one in each fender - and are air-to-water. Radiator is an E-bay special, from an ex-NASCAR car - huge
The car/engine is a 5.4 DOHC engine (believe it came out of a Navigator). Here's a couple of the spec, but I really don't know everything about the complete setup.
Built motor, its got billet rods, probe pistons, race bearings, ARP everything, Sullivan inatake, AEM EMS, AEM C2DI, 160lb injecotrs, 4r75w trans, the list goes on and on, its good to about 1500rwhp. Stock heads if I remember right.
Goal initially will be 900-1000rwhp. This will be a street/strip car. Everything retained except heat and a/c. Even backseats will be in. 10-point Wolfe cage.
Here's link to the initial start up: http://www.youtube.com/watch?v=9oQ1XL0k6SA
I'll try to get Ryan to answer any questions if need be.
Here's some pictures.
David
Most of the engine work was done by the owner of the car (Ryan) and the fabrication and turbo work done by Joey at Excessive AutoSports. Most of the lay-out of the engine bay and running of wires, piping, etc. was done by Ryan and Joey. The intercooler are twins - one in each fender - and are air-to-water. Radiator is an E-bay special, from an ex-NASCAR car - huge
The car/engine is a 5.4 DOHC engine (believe it came out of a Navigator). Here's a couple of the spec, but I really don't know everything about the complete setup.
Built motor, its got billet rods, probe pistons, race bearings, ARP everything, Sullivan inatake, AEM EMS, AEM C2DI, 160lb injecotrs, 4r75w trans, the list goes on and on, its good to about 1500rwhp. Stock heads if I remember right.
Goal initially will be 900-1000rwhp. This will be a street/strip car. Everything retained except heat and a/c. Even backseats will be in. 10-point Wolfe cage.
Here's link to the initial start up: http://www.youtube.com/watch?v=9oQ1XL0k6SA
I'll try to get Ryan to answer any questions if need be.
Here's some pictures.
David
Last edited by Navy David SS; 02-02-2007 at 05:23 PM.
#4
Thanks guys. I know this trend is about a Mustang, but the power, the clean set-up, the dedication on both the owners and Joey is awesome. I guess you would have to be here to appreciate the total build. This is the cleanest build I have seen. The car is almost show quality, but will be a "daily driver" and than go to the track and run easy 9's.
Today (Saturday) was suppose to be the initial dyno day, but not sure its going to happen. Today temp: -11* with a wind chill of -30*. **** eat'n South Dakota weather
David
Today (Saturday) was suppose to be the initial dyno day, but not sure its going to happen. Today temp: -11* with a wind chill of -30*. **** eat'n South Dakota weather
David
#6
Originally Posted by turbo'd stang
Good luck with it. I noticed the NMRA banner...he planning on running a class with it?
David
Trending Topics
#13
Originally Posted by skippydn
Did he ever get the chance to dyno it? Later David
I'll keep you all posted on the dyno numbers.
David