8.8 Build
08-19-2009, 04:25 PM
#101
On The Tree
Join Date: Jun 2005
Location: Humble Tx
Posts: 117
Likes: 0
Received 0 Likes
on
0 Posts
i saw that tasa link, its interesting but youd have to rotate the mounting point 90 degrees to the driver side for the torque arm, and i dont know what that'd do to the strength of that bracket
08-19-2009, 06:53 PM
#102
On The Tree
Join Date: Jun 2005
Location: Humble Tx
Posts: 117
Likes: 0
Received 0 Likes
on
0 Posts
well my local junkyard has a bunch of 96-98 mustang gt axles complete with brakes and everything for 100 bucks. so im gonna pick one up in the next week or two, and start building. hope to have the axle ready with 4.10 gears and tracloc by next month when it starts to get cool. gives me a little time to figure out how to do the t/a mounting bracket, as im definitely going to go that route. im just gonna go with the moser 31 splines and get a used set of cclip eliminators. should be plenty beefy, and we'll see how it holds up to 5k rpm launches on slicks. hahaha.
08-23-2009, 10:09 AM
#104
On The Tree
iTrader: (7)
Join Date: Aug 2007
Location: Jackson, Ms
Posts: 103
Likes: 0
Received 0 Likes
on
0 Posts
Hey guys, I have a friend that picked up a 8.8 for his 02 ws6. It has a mount welded on for the torque arm. He has been running that setup for 3 years. It has seen many high 1.30 60fts being behind a forged ls7.
Now as for the 8.8. i have gone through a few and built alot more. I currently have one in my 03 cobra. Simple build, 31 spline mosser axles with a full spool. 8.8 ends with c clip eliminators. my car has seen many 6k plus launches and now sees 5k trans brake launches. I have been beating on my for over 3 years. No problems.
The 9 inch ends are very good. But not a must. Yes the 8.8 ends are more prone to leaking, but can be sealed with a little work.
I am about to build the same setup as in this thread for a buddy that has a 416 lt1.
Great work on the build. and dont be scared to give it hell. The parts are good for it.
Now as for the 8.8. i have gone through a few and built alot more. I currently have one in my 03 cobra. Simple build, 31 spline mosser axles with a full spool. 8.8 ends with c clip eliminators. my car has seen many 6k plus launches and now sees 5k trans brake launches. I have been beating on my for over 3 years. No problems.
The 9 inch ends are very good. But not a must. Yes the 8.8 ends are more prone to leaking, but can be sealed with a little work.
I am about to build the same setup as in this thread for a buddy that has a 416 lt1.
Great work on the build. and dont be scared to give it hell. The parts are good for it.
08-23-2009, 11:02 AM
#105
08-23-2009, 01:34 PM
#106
TECH Fanatic
iTrader: (65)
Join Date: Jun 2006
Location: OKC
Posts: 1,188
Likes: 0
Received 0 Likes
on
0 Posts
I just unexpectedly picked up a complete 8.8, was supposed to pick up a 9 inch housing and the guy had the 8.8 sitting in the corner. Im going to set it up just like you've posted in the next couple of months.
ive been busy 
08-25-2009, 11:31 PM
#113
On The Tree
Join Date: Jun 2005
Location: Humble Tx
Posts: 117
Likes: 0
Received 0 Likes
on
0 Posts
hey 98silver, what backspacing are you using since the axle is shorter then the 10 bolt? i think what i may do is just find some 15x10 mustang pattern Prostars and run those and some cheapo summit stars in the front, that way i can just throw the 8.8 and 4.10 gears in and then upgrade to the moser axles and chevy boltpattern and all that good stuff as money becomes more available. hopefully i'll have some progress pics within the next month.. just need to figure out what backspacing i'll need and start looking for prostars.
08-30-2009, 10:21 PM
#115
TECH Fanatic
iTrader: (65)
Join Date: Jun 2006
Location: OKC
Posts: 1,188
Likes: 0
Received 0 Likes
on
0 Posts
Did you by any chance try to adapt your ls1 brakes to fit? I've got a spare set of backing plates and i think im going to give it a shot to keep cost down, junkyards around here are a bit overpriced.
08-30-2009, 11:56 PM
#116
I got to thinking the other day helping my buddy work on his ranger.....fox body guys use ranger axles to swap to 5 lug axles and brakes. Well if they can swap axles from a ranger to a fox, can I use a ranger rear to put it in my car? It technically should be the same housing minue the upper control arm mounts and will have leaf spring brackets instead of the LCA mounts, but other than that it should be the same width.
Kind of thinking out loud, but its ALOT easier to find a ranger rear end than a mustang rear, I called a buddy and he told me $350 for a 8.8 with 4.10s, rebuilt trac lok, and drum brakes. Too much IMO especially since all I could use are the housing and gears.
Kind of thinking out loud, but its ALOT easier to find a ranger rear end than a mustang rear, I called a buddy and he told me $350 for a 8.8 with 4.10s, rebuilt trac lok, and drum brakes. Too much IMO especially since all I could use are the housing and gears.
08-31-2009, 08:09 AM
#117
TECH Enthusiast
iTrader: (12)
Join Date: Jan 2004
Location: South East Houston
Posts: 586
Likes: 0
Received 0 Likes
on
0 Posts
I agree. It is my understanding that Explorers are the same rear end too and all have trac-lok's and 31 splined axles. I know around here you can buy used Explorers for $500 for the whole truck. I think this is the route I'll take when the time comes...
08-31-2009, 08:50 AM
#118
TECH Resident
iTrader: (7)
Join Date: Jun 2006
Location: Fort Myers FL
Posts: 908
Likes: 0
Received 0 Likes
on
0 Posts
Those with 8.8's, how is the drive ability, and how does it handle? I won't go this route if it's going to handle like ****. I have the option to buy a fully rebuilt 8.8 for 150$ and im considering it, but nothings happening till I know it won't **** up my drive ability. I'm building this car more for road racing then drag.
Last edited by fortmyerspolice; 08-31-2009 at 09:04 AM.
08-31-2009, 09:35 AM
#119
On The Tree
Join Date: Jun 2005
Location: Humble Tx
Posts: 117
Likes: 0
Received 0 Likes
on
0 Posts
explorer will not work. the pumpkin is offset, where mustangs are not, which is what we need. just keep looking, theres junkyards around here with 8.8s with brakes and all for 100 bucks.
08-31-2009, 10:54 AM
#120