ls1 400whp with bolt on's ?
#1
Staging Lane
Thread Starter
Join Date: Nov 2009
Location: SUN VALLEY
Posts: 99
Likes: 0
Received 0 Likes
on
0 Posts
ls1 400whp with bolt on's ?
just wondering if any body achieved it or do u have to get into the engine for these kind of numbers on just bolt on parts?
#5
TECH Regular
iTrader: (1)
Join Date: Nov 2007
Location: oviedo, FL
Posts: 432
Likes: 0
Received 0 Likes
on
0 Posts
i'd say 360-370 would prolly be about peak numbers and thats FULL bolt ons..
most will make 350-360
to the wheels of course, if you want crank hp.. then you'll be able to do that with boltons
most will make 350-360
to the wheels of course, if you want crank hp.. then you'll be able to do that with boltons
Trending Topics
#8
TECH Regular
iTrader: (1)
Join Date: Nov 2007
Location: oviedo, FL
Posts: 432
Likes: 0
Received 0 Likes
on
0 Posts
well you can see the numbers i put down, and mods in my sig..
my buddy has an a4 ws6 with the same mods, in addition to an ls6 intake and UD pully and he put down 350/358, so i'd say its about right..
my buddy has an a4 ws6 with the same mods, in addition to an ls6 intake and UD pully and he put down 350/358, so i'd say its about right..
#12
11 Second Club
iTrader: (8)
Join Date: Aug 2005
Location: Pasadena, CA
Posts: 2,451
Likes: 0
Received 0 Likes
on
0 Posts
made 364 rwhp @ 5500rpm on an M6 car...with TR-55 plugs
Pacesetter 1 3/4 headers, stock LS6 manifold, stock TB, SLP lid and stock MAF descreened.. I had my Moser 12 bolt at the time!! Also I had no cats and Dynamax bullet, H pipe dumped at the time...I also had a LS7 clutch with aluminum FW..
If I still had my 10 bolt Id be making probably 370-ish rwhp... and I could have still went with a EWP, I could have removed my AC belt, I could have removed power steering and I could have still went with a FAST manifold, and a bigger MAF at the time and made more power.
#13
TECH Addict
iTrader: (39)
made 364 rwhp @ 5500rpm on an M6 car...with TR-55 plugs
Pacesetter 1 3/4 headers, stock LS6 manifold, stock TB, SLP lid and stock MAF descreened.. I had my Moser 12 bolt at the time!! Also I had no cats and Dynamax bullet, H pipe dumped at the time...I also had a LS7 clutch with aluminum FW..
If I still had my 10 bolt Id be making probably 370-ish rwhp... and I could have still went with a EWP, I could have removed my AC belt, I could have removed power steering and I could have still went with a FAST manifold, and a bigger MAF at the time and made more power.
Pacesetter 1 3/4 headers, stock LS6 manifold, stock TB, SLP lid and stock MAF descreened.. I had my Moser 12 bolt at the time!! Also I had no cats and Dynamax bullet, H pipe dumped at the time...I also had a LS7 clutch with aluminum FW..
If I still had my 10 bolt Id be making probably 370-ish rwhp... and I could have still went with a EWP, I could have removed my AC belt, I could have removed power steering and I could have still went with a FAST manifold, and a bigger MAF at the time and made more power.
#17
400 horse bolt-ons
It's not happening. with full boltons still no way. no head change or cam change.. no way. I dynoed at 320 with long tubes with cats, dyno tune,slp cat back,vararam corvette cai, msg wires, larger than stock air bridge with ported throttle body, drilled and slotted rotors, 3.42 rear.. all synthetics.. zero weight motor oil, a4 automatic trans, rev extreme catch can, iridium plugs, etc.. I was told if I got a larger mass air and 78 mm throttle body with an ls6 intake I might pick up 15 to 20 horse. tuner said he felt my car was choking at high rpm. vararam offers no help on dyno. kind of disappointing but a fellow their with a 00 camaro dynoes at 318 hp and he had timeslips of 12.20 110 with his setup. says auto cars dont dyno well because of lack of lock up converter. fyi.. Their was a guy their with a 03 z06 with long tube headers and cai and dyno tune did 373 rwhp. fyi.