use before the I pipe, it might eliminate rasp. id rather get a small muffler and put it in the I pipe before going to your cme. do you have a sound clip? wonder how that sounds. 
how to get rid of rasp in exhaust?
how to get rid of rasp in exhaust? I have a 98 camaro m6 with LT headers ORY pipe (no cats) and straight pipes (I pipe goes into a Y pipe then to CME tips). It has a lot of rasp I'm the 2300-2600 rpm range. It is very very loud. I like the smooth deep tone of the exhaust other than the rasp what do I do to get rid of it? Thanks guys and gals!
The flowmaster merge will clean up the sound & you can pick up a couple HP. But if you go this route I'd have a exhaust shop custom make you a y-pipe using the Flowmaster merge & I'd also use 3" off the collector & 4" for the i-pipe. You can buy a dual 3" inlet/4" outlet merge. If your gonna do it might as well get as much power out of it as you can.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo many ppl use 4" over the axel then use a 3" reducer to fit the rear muffler OR you can get a 4" muffler and your done.but i think its useless to go down to 3" before the over axle bend...
many ppl use 4" over the axle then use a 3" reducer to fit the rear muffler OR you can get a 4" muffler and your done.but i think its useless to go down to 3" before the over axle bend...
EDIT: double post ugggh internet connection sucks lol
EDIT: double post ugggh internet connection sucks lol
I love my 4" exhaust. IMO it is one of the best sounding that I have heard. You can by the mufflex kit and it is a perfect fit, but it is pretty tight when it goes over the axle.
like said above a bullet muffler will get rid of it and will give a deeper tone to the exhaust. ive read that the flowmaster merge will work but some people said it didnt work as well for them. imho i think a flowmaster merge would be a great addition to the exhaust see if it works for ya if not throw a bullet in after it. i went strait to a bullet muffler and worked for me. GL
do you have a merge? can you post a video clip? am on stock muffler deciding which way to go..
Mine comes straight off of the ORY into the I pipe (I have an adapter for the 3" to 4" from there) and then it runs 4" all the way back to the magnaflow muffler. The 4" system from mufflex is also a hideaway pipe so no one can see what you are running. I'm at work now so can't get a video yet, but will post one asap. When i was stock with only the 4" it sounded great, but now that i have headers, i don't think there is a better sounding exhaust.
The flowmaster does nothing for rasp.... All it does help exhasut gasses escape better
Now what rid of 98% of my rasp with my GMMG was a 3" powerstick muffler.. And yes I have a FM merge as well
Now what rid of 98% of my rasp with my GMMG was a 3" powerstick muffler.. And yes I have a FM merge as well