True duals Question: Borla xr1 (40085) vs. Magnaflow bullet (14419)
#22
TECH Fanatic
iTrader: (12)
Join Date: Apr 2007
Location: Douglasville, GA
Posts: 1,276
Likes: 0
Received 0 Likes
on
0 Posts
Video Link: http://www.youtube.com/watch?v=J6PGlPH4csg this gives you a decent idea of how they'll sound. I think it sounds too nasty
#23
On The Tree
iTrader: (7)
Join Date: Sep 2012
Location: Huntsville, AL
Posts: 120
Likes: 0
Received 0 Likes
on
0 Posts
I own theagnaflow 14419's. My setup is a three inch h pipe dumped at the rear axle. It is loud as hell. I do set off car alarms idling by in the parking lot (nine times out of ten a honda). How bassy is it? I feel like I'm listening to a test tone while cruising at 1500 to 2200 rpm's. It will make your ears ring. WOT is loud as hell. I constantly get 'I couldn't hear my engine over your car' from a lot of people.
#24
TECH Enthusiast
iTrader: (6)
thats my car... I had them dumped before I put them out back, both setups sound great!
Here's a video with them dumped before the axle. (excuse the squeaky pulley, dirty car, and scratched up rear 1/4 panel... all have been fixed lol)
https://www.youtube.com/watch?v=8b4djYEXTZ0
Here's a video with them dumped before the axle. (excuse the squeaky pulley, dirty car, and scratched up rear 1/4 panel... all have been fixed lol)
https://www.youtube.com/watch?v=8b4djYEXTZ0
#25
TECH Apprentice
Haha that's funny, how's my exhaust treating you?! I love the true duals it sounds AMAZING!!! lol I'll never go back to a y-pipe setup. It's now routed all the way out the back of the car.
#26
TECH Enthusiast
iTrader: (6)
I sold the car a couple of months ago, I hated to go to a catback, but ground clearance was a big issue for me and it was the only way to go. I loved the sound it made, just felt low on power after, but then again it doesn't flow nearly as much as true duals so it explains it, but the new owner seems to love it! Hopefully I'll see you at kemah one of these saturdays so I can finally hear what I wanted to do originally with that exhaust sounds like.
#32
12 Second Club
iTrader: (10)
Do you have a video or soundclip?
I also bought the phab 3" x and have been searching all over for clips of the 14419's or similar but there isnt much on youtube, ls1sounds etc. Like the OP I want a smooth refined tone thats agressive but not too loud.
Currently running bbk lt's, ory, magnaflow catback. The cb is too quiet and the cutout is too loud and raspy. How do the pypes m80's sound? suggest a pair of mufflers?
I also bought the phab 3" x and have been searching all over for clips of the 14419's or similar but there isnt much on youtube, ls1sounds etc. Like the OP I want a smooth refined tone thats agressive but not too loud.
Currently running bbk lt's, ory, magnaflow catback. The cb is too quiet and the cutout is too loud and raspy. How do the pypes m80's sound? suggest a pair of mufflers?
So look for a sound clip soon.
Does suck, you can't find much TD magnaflow bullets floating around. I will make sure I get many desired clips. Idle,Rev,Drive by, WOT drive by.
#34
11 Second Club
Join Date: Aug 2012
Location: Middletown, DE
Posts: 731
Likes: 0
Received 0 Likes
on
0 Posts
#35
TECH Enthusiast
iTrader: (17)
Join Date: May 2004
Location: GA
Posts: 667
Likes: 0
Received 0 Likes
on
0 Posts
I needed to sell my headers and h pipe. A buyer was interested in the whole thing so I sold it. I was starting my twin turbo build and wasn't planning on running any mufflers
Last edited by LT1TA; 04-23-2014 at 12:40 AM.
#36
10 Second Club
iTrader: (21)
Join Date: Oct 2005
Location: Cleveland, Ohio
Posts: 377
Likes: 0
Received 0 Likes
on
0 Posts
Finally got my exhaust changed over, I put the clip in my dyno thread and in the multimedia forum, but in case anyone missed it. 1 7/8" kooks LTs to offroad x-pipe into 3" borla xr1s
#37
TECH Senior Member
iTrader: (8)
thats my car... I had them dumped before I put them out back, both setups sound great!
Here's a video with them dumped before the axle. (excuse the squeaky pulley, dirty car, and scratched up rear 1/4 panel... all have been fixed lol)
https://www.youtube.com/watch?v=8b4djYEXTZ0
Here's a video with them dumped before the axle. (excuse the squeaky pulley, dirty car, and scratched up rear 1/4 panel... all have been fixed lol)
https://www.youtube.com/watch?v=8b4djYEXTZ0