Hedman
Thread Starter
TECH Fanatic
Joined: Nov 2004
Posts: 1,118
Likes: 0
From: TX
Hedman So, after looking at this thread https://ls1tech.com/forums/showthrea...hedman+headers
I'm thinking about giving these a shot. I need something to replace my SLP's with.. I know they're not as nice as kooks and probably dont produce numbers like pacesetters (so don't yell at me to get those, i've already heard all the
kooks/qtp and pacesetter comments i can take). but these sound like they might suit me very well
Does anyone know what kind of ground clearance these give? 2 or so inchese better than my SLP's is all i need. Are they any more difficult to install than my SLP's were?
Thanks!
Dave
I'm thinking about giving these a shot. I need something to replace my SLP's with.. I know they're not as nice as kooks and probably dont produce numbers like pacesetters (so don't yell at me to get those, i've already heard all the
kooks/qtp and pacesetter comments i can take). but these sound like they might suit me very wellDoes anyone know what kind of ground clearance these give? 2 or so inchese better than my SLP's is all i need. Are they any more difficult to install than my SLP's were?
Thanks!
Dave
There is only so much clearance you can have. My pacesetters couldnt be any closer to the bottom of the car so they are tucking as high as possible.
I actually had those headers ordered because the sales person at the place I was ordering them from said they had them in stock only to find out that the y pipe was in stock and shipped and the headers were back ordered. I refused the y pipe and canceled the whole order all together.
I think they look a good deal for the money but I kept getting conflicting reports on primary size. Hedman specs say 1-1/2 stepped to 1-5/8 and if you call Hedman on the phone they will tell you the same thing. But the place I was ordering them from had 1-5/8 stepped to 1-3/4 on their specs.
I actually had those headers ordered because the sales person at the place I was ordering them from said they had them in stock only to find out that the y pipe was in stock and shipped and the headers were back ordered. I refused the y pipe and canceled the whole order all together.
I think they look a good deal for the money but I kept getting conflicting reports on primary size. Hedman specs say 1-1/2 stepped to 1-5/8 and if you call Hedman on the phone they will tell you the same thing. But the place I was ordering them from had 1-5/8 stepped to 1-3/4 on their specs.
The coating will burn off, sooner than you think. Are you planning to sell the car shortly after the install? You'll be replacing these in a few years. IMO, anything less than stainless is a waste of money.
Trending Topics
Teching In
Joined: Oct 2004
Posts: 17
Likes: 0
From: Shreveport, Louisiana
The primaries are 1 5/8 to 1 3/4. I measured them but that was the outside diameter. I went to the Hooker header website and saw that there 1 3/4 headers were the O/D measurement to. I guess they all give O/D.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
Five Reasons the Camaro Was the Most Pivotal Player in the Pony Car Wars 2.0
Brett Foote
