Finished my header install today...
Finished my header install today... Just got done installing my MAC mids and high flow y-pipe. all in all i have to say that it was a pretty easy install. i was expecting alot worse. the driver side header slid right into place, i did have to cut the little square casting of the passenger side of the block to get the new header in, but that was no big deal. I definetly feel a power increase.... especially after 2800 rpms. i would definetly recommend the MAC mids to anyone who is unable or choices(for some reason) not to run longtubes. The headers and y-pipe fit great, and the install only took me about 7-8 hours with hand tools and no lift.
Originally Posted by TheBlurLS1
Glad to hear it went well!
If you did it again, it would only take 4-5 hours.
If you did it again, it would only take 4-5 hours.
Find a friend thats done it before and everything will go much, much easier.
To bad I was the F-ing guinie-pig that had to go first among my group of friends. Now they're all going to be asking me to help them do thiers.
i could definetly do it again in much less time, like i said before, i heard all these horor stories about how hard headers are to install without a lift, i dont see what the big deal was haha. got a few nice scrapes, cuts, and bruses, but it was all worth it when i fired the car up!! and it started!! haha. and RADZ i am in Sterling, va like 2 min from NOVA community college.
To bad I was the F-ing guinie-pig that had to go first among my group of friends. Now they're all going to be asking me to help them do thiers. haha tell me about it, i already have 2 friends with ls1 camaros asking me to help lol
and one with a LT1 t/a ----haha dream on! unless he pays me lots of $$$$$$$
Originally Posted by WhiteKnightZ28
To bad I was the F-ing guinie-pig that had to go first among my group of friends. Now they're all going to be asking me to help them do thiers.
and one with a LT1 t/a ----haha dream on! unless he pays me lots of $$$$$$$
Originally Posted by Blk97WS6
.......and one with a LT1 t/a ----haha dream on! unless he pays me lots of $$$$$$$
Almost as bad as headers on a 96 Cobra. You can't reach a SINGLE BOLT from under the hood, and we had to pull the k-member.
that sucks...i was reading a post on here doing some research on the MACs before i bought them....and a guy was talking about putting headers on the newer 03-04 cobras, god that sounds like hell to do. id be hating life haha. the funny thing is my friend has a 04 cobra with bassani x, borla cat-back, ported blower, 60lb injectors, and now hes looking to do headers on it. you WONT see me helping on that thing. especially because its a ford haha
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
