TORCHD 02 TA

iTrader: (39)

i will have to listen to hear in a bit. But what does 'against the grain' mean? got a pic to show me?

TORCHD 02 TA

iTrader: (39)

ok i listened to the clip...

The power stick got rid of i would say 95% of the rasp. The rasp was present for about 2 seconds then gone

Now as far as the sound goes. Was video clip #1 and video clip #2 both shot with the same camera? Video clip #2 sounded a little quieter with the power stick. Just wondering. SOudns good

97camarozguy

iTrader: (5)

No, they were shot with different cameras. Vid #1 was shot with a canon elph, and vid #2 was shot with my new casio exilim. This was the first vid that was taken with it so I didn't know how it would turn out. I actually got my muffler from stainless works so it isn't a "power stick" but it's pretty much the same thing. When I say against the grain, I am talking about the baffling inside the muffler. Against the grain is quieter than with the grain if that makes any sense.

With the grain:


Against the grain:

sixpack_2_go

iTrader: (1)

yes do it. it will sound amazing!

bluchev

do it! should sound badass

97camarozguy

iTrader: (5)

To me, it honestly sounds alot like the catted y. Not sure which one flows better or anything, I just made the mistake of not getting a catted y in the first place.

Beasst8

iTrader: (1)

I love the GMMG sound. I run LT's, ORY and Open Cutout. Now thats RASP. But the wife LOVES it.

TORCHD 02 TA

iTrader: (39)

so with your 2nd pic agianst the grain. The top portion that you took a pic of, you put in the in the I pipe with that portion facing the nose of the car correct?

JScamaro

iTrader: (6)

I don't know if the design is the same for the gmmg and the one you got. Gmmg will sell an extra muffler separate to weld in the I pipe.

I know you used different cameras but I think the first video sounded better.

TORCHD 02 TA

iTrader: (39)

Do you have a pic of the muffler that they sell?

97camarozguy

iTrader: (5)

Yes, the angle in the against the grain pic would be where the air flows into the muffler.

ynkssws6

iTrader: (1)

Common mistake. Do it once. Do it right.

spm4520

iTrader: (5)

Can someone explain what everyone is talking about when they say RASP? I have stock exhaust right now and don't want a bad sounding exhaust when I upgrade. I listened to both sound clips and all i hear is the second being quieter. What is RASP?

TORCHD 02 TA

iTrader: (39)

if you listen to this sound clip between 7 seconds and 6 seconds that is rasp.. it makes that blaaaat sound



Here is my sound clip.. at 10 seconds same thing

97camarozguy

iTrader: (5)

Most cars get it somwhere between 2000-2500 rpms. It sounds like a damn jackhammer from inside the car.

TORCHD 02 TA

iTrader: (39)

Hey i forgot to ask you. How long is that resinator that you bought?

97camarozguy

iTrader: (5)

It's a 30 incher. That was the only length I saw when I was ordering it. I ended up cutting that little part off the y-pipe that is necked down so all I had was the 3" part. Then I just cut two small slits in the front end of the muffler and put a clamp around it and the back side was just trial and error to make it fit good. Measure twice, cut once. The i-pipe that comes with the catback slips right inside the muffler like that's what it was meant to do. After I got the back piece with the elbow to fit right, I just welded it in, put it all back together and took it for a ride.

blu byu EH

iTrader: (25)

Very Nice!!!! They Need To Make This A Sticky

JScamaro

iTrader: (6)

When I asked Gmmg they said they would custom make another Gmmg chambered muffler to weld in the I pipe at whatever size needed. I don't know what they look at from the inside though.

97camarozguy

iTrader: (5)

I wish I would have known that! I wonder what they will charge for them.